spacer

















spacer
Aguilar Preamps

Aguilar OBP-2 Onboard Bass Preamp

Aguilar OBP-2 Bass Preamp


The custom prewired units below include wiring all of the following for whatever configuration you have chosen:
  • Potentiometers
  • Switches
  • Battery connectors
  • Output Jack

The Output Jack is a standard switchcraft panel jack. If you require a long threaded barrel jack you will need to make the connections to your long threaded barrel jack as your bass isn't on our bench!

Switches are standard black flat mini-toggle. Black round bat, Chrome Flat, & Gold Flat are available during configuring your preamp.

Since your bass isn't on our bench there are a couple connections you will have to make including wiring the pickups to the preamp, grounding the wire from the bridge to the output jack, and possibly the jack if it is not the common style sterero panel jack that is included.


Prewiring is done every couple of days. Typical wait is just 4-5 days before leaving our shop.


Shipping Note on Prewired Units:

Prewired units are created based on your individual order.

This means that our technicians are custom wiring your order within days of completing your order with Best Bass Gear.

If you choose expedited shipping options that does not expedite the time taken to custom wire your particular item.

2 Pickup, 2 Knob

---------------------------------------------------------------------------------------

2 Pickup, 2 Knob, 1 Switch

---------------------------------------------------------------------------------------

2 Pickup, 3 Knob

---------------------------------------------------------------------------------------

2 Pickup, 3 Knob, 1 Switch

---------------------------------------------------------------------------------------

2 Pickup, 4 Knob

---------------------------------------------------------------------------------------

2 Pickup, 4 Knob, 1 Switch

---------------------------------------------------------------------------------------

1 Pickup, 2 Knob

---------------------------------------------------------------------------------------

1 Pickup, 2 Knob, 1 Switch

---------------------------------------------------------------------------------------

1 Pickup, 3 Knob

---------------------------------------------------------------------------------------

1 Pickup, 3 Knob, 1 Switch


---------------------------------------------------------------------------------------


Custom Prewiring: email us ~ sales@bestbassgear.com

Aguilar OBP-2

The OBP-2 was designed to give bassists fat tone while being small enought fit into tight control cavities. Wire this preamp with one 9 volt battery and it will fit into just about any instrument. With +/-18dB of boost and cut at 40Hz and +/- 16dB of treble boost and cut at 6.5 kHz you have can emphasize just the right frequencies to make your bass sound great in any mix.

The Aguilar OBP2 small size makes it an easy retrofit in almost any bass. Combining high headroom and low noise, the OBP-2 is unmatched in providing tonal flexibility while retaining the true character of any bass!

Pickup Compatibility:

The preamp can be used with active or passive pickups.

On the configuration page there is an option for pickup impedance.

If you have passive pickups like Bartolini ®, Nordstrand ®, Aguilar ®, Seymour Duncan ®, and others then choose "For Passive Pickups"

If you have active pickups such as EMG®, Warwick® MEC, and others then choose "For Active Pickups".

Specifications:

  • Bass Control: plus/minus 18 dB @ 40 Hz.
  • Treble Control: plus/minus 16 dB @ 6.5 KHz.
  • Input Impedance: 1 meg ohm
  • Output Impedance: 100 ohm
  • Power Requirements:9 or 18 volts operation. Additional 6dB headroom with 18 volts..
  • Distortion: .019 into 10k ohm load
  • Noise: -95 dBm unweighted.
  • Battery life: 324 hours
  • Wire Lead Length: 6.50 inches
  • Input Stage:Low noise discrete FET input stage, center detent 50 K linear pots,with a dual concentric pot available.
  • Dimensions: 0.98"W x 0.98"L x 0.59"D
  • Three year limited warranty.