Glockenklang Bass Preamp Wiring Diagrams

Glockenklang onboard bass preamp wiring diagrams as text: all three Glockenklang sheets in our library, with the 1-A to 9-I terminal key written out connection by connection.

Before you start

  • The jack switches the battery: battery − goes to the jack's middle (ring) lug.
  • Bridge pickup to In1, neck to In2 on the balance pot.
  • Where the drawing has no key, the page says what goes where and points you to the drawing (FUNCTION-LEVEL).

On this page

Glockenklang onboard preamp hookup: the 1-A to 9-I key

Glockenklang's volume control is a small board with nine numbered terminals. The key on the sheet pairs each number with a letter: 1 goes to A, 2 to B, and so on to 9 and I. The letters are on the jack, the balance pot, the bass board and the treble pot.

Glockenklang onboard preamp hookup: the 1-A to 9-I key: wire by wire
#FromToNotes
1Volume board terminal 1Jack lug A, OutputWhite
2Volume board terminal 2Jack lug B, GroundBlack
3Volume board terminals 3 and 4Balance pot terminals C and DTwo-pin connector on the balance pot
4Volume board terminals 5, 6, 7Bass board terminals E, F, GThree-pin block on the bass board
5Volume board terminals 8, 9Treble pot terminals H and I
6Bridge pickup hotBalance pot In1
7Neck pickup hotBalance pot In2
8Pickup grounds / shieldBalance pot Shield (Ground)
9Battery +Bass board +9 Volt terminal
10GroundBass board Ground terminal
11Battery −Jack middle lug (ring)Labelled '− Battery'
12Mid boardBass board headerRibbon cable, as drawn

Step by step

  1. Mount the pots and boards and ground the cavity.
  2. Wire the pickups to the balance pot: bridge to In1, neck to In2, grounds to Shield.
  3. Connect volume board terminals 1 to 9 to the matching letters A to I: output and ground on the jack, C/D on the balance, E/F/G on the bass board, H/I on the treble pot.
  4. Battery + to the bass board's +9 Volt terminal, battery − to the jack's middle lug, ground to the bass board's Ground terminal.
  5. Connect the mid board to the bass board with its ribbon, plug in and test.

See also

Volume P/P Active/Passive, Blend, Treble, Mid, Bass

Five knobs: push-pull volume for active/passive, balance (blend), and separate treble, mid and bass.

Volume P/P Active/Passive, Blend, Treble, Mid, Bass: controls and specs
ControlsVolume (push-pull active/passive), Balance, Treble, Mid, Bass
PickupsTwo: In1 bridge, In2 neck
Power+9 V to the bass board
Glockenklang onboard preamp wiring diagram, volume blend treble mid bass
Glockenklang's drawing. Click to enlarge, or download the PDF.

See also

Volume P/P Active/Passive, Blend, Treble/Bass Stack, Mid

Four knobs: the treble and bass share a stacked pot. The wiring key is the same 1-A to 9-I.

Volume P/P Active/Passive, Blend, Treble/Bass Stack, Mid: controls and specs
ControlsVolume (push-pull active/passive), Balance, stacked Treble/Bass, Mid
PickupsTwo: In1 bridge, In2 neck
Power+9 V to the bass board
Glockenklang onboard preamp wiring diagram with stacked treble bass
Glockenklang's drawing. Click to enlarge, or download the PDF.

See also

Volume P/P Active/Passive, Treble, Bass, Mid (one pickup)

Single-pickup version: no balance pot. The pickup's In and Shield (ground) leads go straight to the volume board.

FUNCTION-LEVEL: this sheet has no number key. Follow the drawing for which volume-board terminal takes the pickup, the jack and the treble pot.

Volume P/P Active/Passive, Treble, Bass, Mid (one pickup): controls and specs
ControlsVolume (push-pull active/passive), Treble, Bass, Mid
PickupOne: In and Shield (Ground) to the volume board
JackGround, − Battery (ring), Output
Power+9 V to the bass board
Glockenklang onboard preamp wiring diagram for one pickup
Glockenklang's drawing. Click to enlarge, or download the PDF.

FAQ

What does 1-A, 2-B on the Glockenklang sheet mean?

Each numbered terminal on the volume board connects to the terminal with the matching letter: 1 to A (jack output), 2 to B (jack ground), 3 and 4 to the balance pot (C, D), 5 to 7 to the bass board (E, F, G), 8 and 9 to the treble pot (H, I).

Where does the battery go on a Glockenklang preamp?

Battery + goes to the +9 Volt terminal on the bass board and battery − to the jack's middle (ring) lug, so the preamp turns on when a cable is plugged in.

Back to all bass wiring diagrams