Noll Bass Preamp Wiring Diagrams

Noll bass preamp wiring diagrams as text: TCM 2, TCM 3 and TCM 4XM modules, the TCM 3P/3PM parametric, plus the PA1 and MixPot modules, all from Noll's own sheets. Find your module, then follow the shared hookup for the balance pot, push-pull volume and stereo jack.

Before you start

  • Noll TCM modules are powered through a stereo jack: battery − to the ring, so plugging in turns the preamp on.
  • EQ pots are 50K linear on the TCM 2, 3 and 4XM.
  • For one pickup, leave out the balance pot and wire the pickup to the volume pot.
  • Spots where the drawing is too busy to read lead by lead are marked FUNCTION-LEVEL.

On this page

TCM 2, TCM 3 and TCM 4XM

Noll TCM hookup: balance, push-pull volume, stereo jack and battery

This is the passive side and power that TCM 2, TCM 3 and TCM 4XM share, taken off Noll's drawings. The only difference between those three is how many EQ pots hang off the module.

Noll draws a 5-lug "special dualaudio" balance pot and a push-pull volume. Lugs below are named by where they sit on the drawing (the push-pull switch is the 2 x 3 block under the pot lugs).

FUNCTION-LEVEL: Noll's drawing doesn't say whether pushed or pulled is active. The switch connects the middle lug to the top lug in one position (passive) and to the bottom lug in the other (active). Check with the bass plugged in at low volume.

Noll TCM hookup: balance, push-pull volume, stereo jack and battery: wire by wire
#FromToNotes
1Neck pickup hotBalance pot, bottom row lug 1 (far left)Labelled 'Neck PU'
2Pickup ground(s)Balance pot, lug 2Labelled 'PU GND'
3Bridge pickup hotBalance pot, lug 3Labelled 'Bridge PU'
4Common groundBalance pot, lug 4Labelled 'Common GND'; ties to your ground bus
5Balance pot lug 5 (output)TCM module input (light grey/white lead)Same point also runs to the push-pull switch, next row
6Balance pot lug 5 (output)Push-pull switch, right column, top switch lugThis is the passive feed
7TCM module output (blue)Push-pull switch, right column, bottom lugThis is the active feed
8Push-pull switch, right column, middle lugVolume pot input lug (right-hand pot lug)Short jumper; the middle lug is the switch common
9Volume pot wiper (middle pot lug)Stereo jack tipBlue on the drawing
10Volume pot left lugGround
11TCM module redBattery + (9 V)
12Battery − (black)Stereo jack ringPlugging in a mono lead joins ring to sleeve and powers the module
13Stereo jack sleeve and the module ground leadGround

Step by step

  1. Ground the cavity and run a common ground point; the balance pot's Common GND lug, the volume pot's left lug, the jack sleeve and the module ground all go there.
  2. Wire the pickups to the balance pot: neck hot to lug 1, pickup grounds to lug 2, bridge hot to lug 3, common ground to lug 4.
  3. Run the balance output (lug 5) to the TCM module input and to the top lug of the push-pull switch's right column.
  4. Run the TCM module output (blue) to the bottom lug of that column, and jumper the middle lug to the volume pot's input lug.
  5. Volume wiper to jack tip, volume left lug to ground.
  6. Module red to battery +, battery − to the jack ring, jack sleeve to ground.
  7. Wire each EQ pot to the module with its three leads (see your model below), plug in and check both switch positions.

See also

Noll TCM 2 (2-band: bass, treble)

Two-band module. Bass and treble are 50K linear pots, each wired to the module with three leads.

Noll TCM 2 (2-band: bass, treble): controls and specs
EQ potsTreble 50K lin, Bass 50K lin
Power9 V, switched by the stereo jack
Treble pot leadsDark red to the left lug, black (dashed) to the middle, grey to the right, as drawn
Bass pot leadsGreen to the left lug, black (dashed) to the middle, yellow to the right, as drawn
Single pickupLeave out the balance pot and wire the pickup straight to the volume pot (Noll's note)
Noll TCM 2 bass preamp wiring diagram
Noll's drawing. Click to enlarge, or download the PDF.

See also

Noll TCM 3 (3-band: bass, mid, treble)

Same as the TCM 2 with a third pot for midrange. All three EQ pots are 50K linear and connect to the module with three leads each.

Noll TCM 3 (3-band: bass, mid, treble): controls and specs
EQ potsTreble, Bass, Midrange: 50K lin each
Power9 V, switched by the stereo jack
EQ pot leadsThree per pot; follow the drawing for the colours on each pot
Single pickupLeave out the balance pot and wire the pickup straight to the volume pot
Noll TCM 3 bass preamp wiring diagram
Noll's drawing. Click to enlarge, or download the PDF.

See also

Noll TCM 4XM (4-band: bass, low mid, high mid, treble)

Four bands, four 50K linear pots, same passive side and jack as the TCM 2 and 3.

Noll TCM 4XM (4-band: bass, low mid, high mid, treble): controls and specs
EQ potsBass, Treble, Low Mid, High Mid: 50K lin each
Power9 V, switched by the stereo jack
EQ pot leadsThree per pot; follow the drawing for the colours
Single pickupLeave out the balance pot and wire the pickup straight to the volume pot
Noll TCM 4XM 4-band bass preamp wiring diagram
Noll's drawing. Click to enlarge, or download the PDF.

See also

TCM 3P / TCM 3PM (parametric)

Noll TCM 3P / TCM 3PM (3-band with frequency controls, 18 V)

Each band gets a dual concentric pot: boost/cut on one ring, frequency on the other (bass, midrange, treble). Our library lists the TCM 3PM under this same sheet.

The balance pot, push-pull volume and pickup leads are wired exactly like the TCM hookup. What changes is power: Noll draws two 9 V batteries and a 9-lug stereo jack so plugging in switches both batteries in series for 18 V.

FUNCTION-LEVEL: the nine-lug EQ pots and the 9-lug jack carry many leads that cross on the drawing. Follow Noll's drawing lug for lug for the EQ pots and the battery/jack wiring.

Noll TCM 3P / TCM 3PM (3-band with frequency controls, 18 V): controls and specs
ControlsBass boost/cut + bass frequency; Midrange boost/cut + mid frequency; Treble boost/cut + treble frequency (three dual concentric pots)
Power18 V recommended by Noll (two 9 V batteries)
Jack9-lug stereo jack only (Noll's note)
Module outputBlue lead to the push-pull switch, as on the TCM 2
Single pickupLeave out the balance pot and wire the pickup straight to the volume pot
Noll TCM 3P parametric bass preamp wiring diagram, 18 volt
Noll's drawing. Click to enlarge, or download the PDF.

Modules

Noll PA1 module

A small preamp module with four leads and a gain trim.

Noll PA1 module: controls and specs
Gain trimOn the module, up to +15 dB
Noll PA1 module: wire by wire
#FromToNotes
1PA1 blackGround
2PA1 whiteInput (from the pickup or control)
3PA1 blueOutput (towards the jack)
4PA1 red+9 V
Noll PA1 module wiring diagram
Noll's drawing. Click to enlarge, or download the PDF.

Noll MixPot module (piezo / magnetic mixer)

Two-channel mixer on a pot: channel 1 is labelled for a piezo, channel 2 for a magnetic pickup.

Noll MixPot module (piezo / magnetic mixer): controls and specs
TrimsGain channel #1 (left side) and gain channel #2 (right side)
Noll MixPot module (piezo / magnetic mixer): wire by wire
#FromToNotes
1Input channel 1 / piezo hotMixPot top pin 1 (left)
2Pickup groundTop pin 2
3Pickup groundTop pin 3
4Input channel 2 / magnetic hotTop pin 4 (right)
5Red battery wire (+9 V)Right side, middle pin
6MixPot outputJack tipRight side, lower pin
7Common ground (optional)Bottom left pin
Noll MixPot piezo and magnetic pickup mixer wiring diagram
Noll's drawing. Click to enlarge, or download the PDF.

FAQ

Why does a Noll preamp need a stereo jack?

The battery's minus lead goes to the jack's ring. A mono cable joins ring and sleeve, which completes the battery circuit, so the preamp only draws power while a cable is plugged in.

Can I use a Noll TCM with one pickup?

Yes. Noll says to leave out the balance pot and wire the pickup straight to the volume pot.

What pots do the Noll TCM modules use?

50K linear for every EQ band on the TCM 2, TCM 3 and TCM 4XM. The TCM 3P uses dual concentric pots, boost/cut plus frequency on each band.

Does the TCM 3P run on 9 or 18 volts?

Noll recommends 18 V, using two 9 V batteries and a 9-lug stereo jack.

Back to all bass wiring diagrams