Stellartone ToneStyler Wiring Diagrams

Stellartone ToneStyler wiring as text: the single-cable ToneStyler, the two-cable DUO for J-Basses, and Stellartone's diagram 2.2 for a J-Bass with volume, blend and ToneStyler.

Before you start

  • Red is hot, the copper shield is ground, and the clear wire is a floating ground you normally solder to the shield.
  • Never wire a ToneStyler to a volume pot's output.

On this page

ToneStyler with single cable (standard, non-Duo)

For P-Bass and other one-volume basses. The ToneStyler solders straight to the pickup output.

For basses with two pickups: use one ToneStyler per pickup, or on a master-volume bass one ToneStyler on the blend pot or pickup selector output. Never on the volume pot's output (Stellartone's warning).

ToneStyler with single cable (standard, non-Duo): wire by wire
#FromToNotes
1RedPickup output (hot)HOT
2ClearGroundFloating ground; for typical installs solder it together with the shield
3Copper shieldGround

Step by step

  1. Find the pickup's hot output (or the blend/selector output on a master-volume bass). Not the volume pot output.
  2. Solder the ToneStyler's red wire to that point.
  3. Twist the clear wire and copper shield together and solder them to ground.
  4. Mount the ToneStyler in the old tone pot hole and test.
Stellartone ToneStyler single cable wiring, red hot clear floating ground shield ground
Stellartone's drawing. Click to enlarge, or download the PDF.

See also

ToneStyler DUO (two cables, for J-Bass and other vol-vol-tone basses)

The DUO has two cables, one per pickup, so a J-Bass keeps both volume knobs.

ToneStyler DUO (two cables, for J-Bass and other vol-vol-tone basses): wire by wire
#FromToNotes
1Neck cable redNeck pickup outputHOT
2Neck cable clearGroundFloating ground; solder with the shield for typical installs
3Neck cable copper shieldGround
4Bridge cable redBridge pickup outputHOT
5Bridge cable copper shieldGroundThe bridge cable has no clear wire
Stellartone ToneStyler DUO two cable wiring for J-Bass
Stellartone's drawing. Click to enlarge, or download the PDF.

J-Bass: Volume, Blend, ToneStyler (Stellartone diagram 2.2)

Stellartone 2.2: replace the tone pot with a ToneStyler and the bridge pickup volume with a blend pot, for J-Basses with two volumes and one tone.

This sheet is for "A-C" style blend pots. The inside deck (lugs 3-2-1) is the clockwise A taper and takes the neck pickup; the outside deck (lugs 6-5-4) is the counter-clockwise C taper and takes the bridge pickup.

FUNCTION-LEVEL: the ToneStyler's red wire and the jumpers between the blend decks and the volume pot are small on this sheet. Follow the drawing for the exact lugs; the jack tip comes from the volume pot.

J-Bass: Volume, Blend, ToneStyler (Stellartone diagram 2.2): controls and specs
ControlsVolume, Blend (A-C dual taper), ToneStyler
Blend pot examples (Stellartone)Bourns EP-5386, CGE WD500PAN, Alpha (old style)
GroundsBlack wires from neck and bridge pickups, the ToneStyler's clear wire and the bridge-plate ground all go to ground (volume pot casing / jack sleeve)
Pickup hotsWhite from neck pickup to the inside (A) deck, white from bridge pickup to the outside (C) deck
Stellartone diagram 2.2 J-Bass volume blend ToneStyler wiring
Stellartone's drawing. Click to enlarge, or download the PDF.

FAQ

Can I wire a ToneStyler after the volume pot?

No. Stellartone says never connect it to a volume pot's output. Wire it to the pickup output, or to the blend or selector output on a master-volume bass.

Which ToneStyler do I need for a Jazz Bass?

The two-cable ToneStyler DUO, so each pickup keeps its own volume. If you swap the bridge volume for a blend pot, the single-cable ToneStyler works as in Stellartone diagram 2.2.

What is the clear wire on a ToneStyler?

A floating ground. For typical installs Stellartone says to solder it together with the copper shield to ground.

Back to all bass wiring diagrams