Seymour Duncan STC-3M3 / STC-3M4 Wiring Diagram
The Basslines (Seymour Duncan) Tone Circuit is a 3-band EQ made for Music Man basses. The STC-3M3 and STC-3M4 use the same preamp with a different harness. The 3M4 has separate bass and treble pots for 4-knob basses. The 3M3 stacks bass and treble on one concentric pot for 3-knob basses. The boards are identical and the harnesses are interchangeable. The STC_3M4 PDF on our site is the same document.


Before you solder
- The standard controls come prewired. Unplug the two connectors (color-coded blue and red), mount the pots, then plug them back into the same spots.
- Pots shown: master volume 10k push/pull, plus treble, mid-range and bass at 100k.
- Red is +9V and goes to battery hot; insulate it. The black wire that joins the pot shells goes to the jack ground (sleeve).
- Battery black goes to the ring of a stereo output jack. Tip is hot output (the white wire from the center of the volume pot).
- Gray is the preamp input. The pickup's red and black join together as the pickup's hot output.
- Basslines Music Man pickups (SMB-4A, 4D, 5A, 5D) are designed for parallel. Series also works and gives a hotter sound with more mid-range.
- The series/split/parallel option uses a 3-way blade switch and a 3.3k resistor (Fig. 2).
- Slap contour: two trimpots on the board preset the mid cut and bass boost (Fig. 3).
- Velcro the board into the cavity, with nothing on the board touching the backs of the pots.
Every diagram, wire by wire
The STC-3M3 / STC-3M4 hookup as text: what to connect, wire by wire, plus the pickup color code for parallel and series.
- Seymour Duncan STC-3M3 / STC-3M4: pickup and jack hookup
- Basslines Music Man pickups (SMB-4A, 4D, 5A, 5D): parallel or series
How to read these
- Ground means the back of a pot casing (or the jack sleeve). Join all pot casings with a bare wire so they share one ground.
- The stereo jack's ring grounds the battery only with a plug in, which turns the preamp on.
Seymour Duncan STC-3M3 / STC-3M4: pickup and jack hookup
The STC harness comes prewired to its pots (10K push/pull master volume, 100K treble, mid and bass). You connect the pickup, the battery and the stereo jack.
You need: STC-3M3 or STC-3M4 preamp with harness, Music Man-style humbucker, 9V battery clip, stereo output jack.
| # | From | To | Notes |
|---|---|---|---|
| 1 | Pickup: Red + black (joined) | STC harness: GRAY (input) | The pickup's hot output into the preamp |
| 2 | Pickup: Green | Ground (back of a pot casing) | |
| 3 | Pickup: White | Ground (back of a pot casing) | |
| 4 | Pickup: Bare | Ground (back of a pot casing) | |
| 5 | 9V battery: Red (+) | STC harness: RED (+9V) | The red wires join here |
| 6 | STC harness: WHITE (output) | Stereo jack: Tip | Hot output from the center of the volume pot |
| 7 | STC harness: BLACK (pot casings) | Stereo jack: Sleeve | Ground from the pot casings |
| 8 | 9V battery: Black (−) | Stereo jack: Ring | Plugging in turns the preamp on |
Step by step
- Unplug the connectors. Remove the two connectors from the circuit board (they are color coded blue and red) so you can fit the pots without bending the wires.
- Fit the pots. Remove old pots you won't use and install the new ones in their places.
- Pickup. Join the pickup's red and black wires and solder them to the GRAY preamp input. Green, white and bare go to ground (a pot casing).
- Power. Solder the battery red to the preamp RED (+9V) and insulate the joint. Battery black goes to the ring of the stereo jack.
- Output. WHITE (from the center lug of the volume pot) to the jack tip; BLACK (joins all pot casings) to the jack sleeve.
- Reconnect. Plug the two connectors back onto the board in their color-coded places, then fix the board in the cavity with the Velcro so no part touches the pot backs.
- Test. Plug in at low volume and tap each pickup's pole pieces with a screwdriver. Turn each knob end to end before closing the cavity.
- STC-3M3 and STC-3M4 are the same preamp: the 3M3 stacks bass and treble on one concentric pot (3 knobs), the 3M4 splits them (4 knobs). The harnesses swap.
- The master volume's push/pull switches the slap contour. Trimpots on the board set its bass boost and mid cut.
Basslines Music Man pickups (SMB-4A, 4D, 5A, 5D): parallel or series
These pickups are built to run in parallel. Series also works and gives a hotter sound with more mid-range.
| Wiring | Hot output | Join and tape | To ground |
|---|---|---|---|
| Parallel (standard) | Red and black, joined | - | Green, white, bare |
| Series | Black | Red and white | Green, bare |
Step by step
- Pick parallel or series. Use the table: parallel is standard; series is louder with more mids.
- Wire the hot. Send the hot output (red+black for parallel, black for series) to the preamp's GRAY input.
- Test. Plug in at low volume and tap each pickup's pole pieces with a screwdriver. Turn each knob end to end before closing the cavity.
- The sheet's Fig. 2 adds a 3-way blade switch for series, single coil and parallel, with a 3.3K resistor. Follow that drawing lug by lug.
Parts in this diagram
FAQ
What's the difference between the STC-3M3 and STC-3M4?
Only the harness. The 3M4 has separate bass and treble pots for 4-knob basses. The 3M3 has a stacked bass/treble pot for 3-knob basses. The circuit boards are identical.
Do I need a stereo jack?
Yes. Battery black goes to the ring terminal of a stereo output jack.
Should the pickup be wired series or parallel?
The Basslines Music Man pickups are designed for parallel. Series works too and gives a hotter, more mid-heavy sound.
Can I adjust the slap contour?
Yes. Two trimpots on the board set the amount of mid cut and bass boost.
Related diagrams
Questions about your install? Email sales@bestbassgear.com.