Aguilar OBP-2 Wiring Diagrams

Aguilar's OBP-2 is a 2-band (bass and treble) onboard preamp. This page has 20 OBP-2 hookups: Aguilar's four (blend and volume, bypass switch, stacked tone pot, two volumes) and 16 drawn by Best Bass Gear: one pickup, two volumes, stacked volumes, a volume/tone stack, push-pull or mini-switch active/passive, and passive tone. All pots are shown from the rear.

OBP-2 wiring with blend and volume control
OBP-2 wiring with blend and volume control
OBP-2 wiring with blend, volume and DPDT bypass switch
OBP-2 wiring with blend, volume and DPDT bypass switch
OBP-2 wiring with blend, volume and stacked tone pot
OBP-2 wiring with blend, volume and stacked tone pot
OBP-2 wiring with two volume controls
OBP-2 wiring with two volume controls
OBP-2 with one pickup: volume, treble, bass
OBP-2 with one pickup: volume, treble, bass
OBP-2 with one pickup: volume and treble/bass stack
OBP-2 with one pickup: volume and treble/bass stack
OBP-2 volume, volume, treble, bass with active/passive switch
OBP-2 volume, volume, treble, bass with active/passive switch
OBP-2 push/pull active/passive volume, blend, treble, bass
OBP-2 push/pull active/passive volume, blend, treble, bass

PDFs: Aguilar OBP-2 wiring diagram (4 pages) · OBP-2 volume, treble, bass · OBP-2 volume, treble/bass stack · OBP-2 volume, volume, treble, bass, active/passive switch · OBP-2 volume (push/pull active/passive), blend, treble, bass

Before you solder

  • Bass and treble pots are 50K linear. Stacked versions use one dual 50K linear pot.
  • Power is two 9V batteries in series (18V), or one 9V. The output must be a stereo jack: inserting a 1/4" plug powers the OBP-2.
  • Blend (dual audio) and volume values depend on your pickups. Use the values your pickup maker recommends.
  • Single pickup: leave out the blend pot and wire the pickup straight to the volume pot.
  • On a standard jack, the tip lug sits across from the actual tip, and the ground lug is the center lug.

Every diagram, wire by wire

All 20 OBP-2 layouts as text, with a connection diagram and wire table for each hookup.

How to read these

  • Pots are shown from the back with the lugs up. 'Left', 'middle' and 'right' lug mean that view.
  • Module wires use Aguilar's color names (BRN, GRY, VIO, WHT, YEL, VIO/WHT, BLU, GRN, BLK, RED).
  • Ground means the back of a pot casing (or the jack sleeve). Join all pot casings with a bare wire so they share one ground.
  • The stereo jack's ring connects battery − to ground only when a plug is in, so unplug the bass when you're not playing.

Aguilar OBP-2 with blend and volume (2 pickups)

Two passive pickups into a dual-audio blend and a volume, then the OBP-2 module with bass and treble pots, two 9V batteries in series (18V) and a stereo jack that turns the preamp on.

You need: OBP-2 module, 2 pots 50K linear (bass, treble), dual-audio blend pot, volume pot (value to suit the pickups), 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with blend and volume (2 pickups)Two passive pickups into a dual-audio blend and a volume, then the OBP-2 module with bass and treble pots, two 9V batteries in series (18V) and a stereo jack that turns the preamp on. Wire numbers match the wire table.1234567891011121314Bridge pickupHotGroundNeck pickupHotGroundBlenddual audioGang A middleGang B middleOutput lugsGround lugsVolumeLug 3 (in)Lug 2 (out)Lug 1Bass + treble pots50K linear6 lugs (table)OBP-2 moduleBLU (input)GRN (output)BLK (ground)RED (+ power)EQ wires (6)Stereo jackTipRingSleeve (ground)2 x 9V in series+ (18V)−Ground: pot casings, jack sleeve and cavity shielding, all joined
Aguilar OBP-2 with blend and volume (2 pickups), redrawn as a connection diagram. Original drawing: Aguilar OBP-2 wiring diagram (4 pages), page 1.
Aguilar OBP-2 with blend and volume (2 pickups): wire by wire
#FromToNotes
1Bridge pickup: HotBlend: Gang A middle
2Neck pickup: HotBlend: Gang B middle
3Bridge pickup: GroundGround (back of a pot casing)
4Neck pickup: GroundGround (back of a pot casing)
5Blend: Output lugsVolume: Lug 3 (in)Both gang outputs joined
6Blend: Ground lugsGround (back of a pot casing)
7Volume: Lug 1Ground (back of a pot casing)
8Volume: Lug 2 (out)OBP-2 module: BLU (input)Into the preamp
9OBP-2 module: GRN (output)Stereo jack: TipPreamp output
10OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)Module ground
11Stereo jack: Sleeve (ground)Ground (cavity / pot casings)
12OBP-2 module: RED (+ power)2 x 9V in series: + (18V)
132 x 9V in series: −Stereo jack: RingPlugging in turns the preamp on
14Bass + treble pots: 6 lugs (table)OBP-2 module: EQ wires (6)See the EQ table
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Bass 50K linearBRNGRYVIO
Treble 50K linearWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the blend, volume, bass and treble pots and the stereo jack. Join the pot casings with a bare wire so they share one ground.
  2. Pickups to the blend. Solder the bridge pickup hot to the middle lug of one blend gang and the neck pickup hot to the middle lug of the other. Pickup grounds go to a pot casing.
  3. Blend outputs. On each gang, join one outer lug to the other gang's opposite outer lug and run that to volume lug 3. The remaining outer lug of each gang goes to ground, so the two gangs fade in opposite directions.
  4. Volume to the module. Volume lug 1 to ground. Volume lug 2 (middle) to the module's BLU wire.
  5. EQ pots. Solder the module's six EQ wires to the bass and treble pots exactly as in the table: bass gets BRN, GRY, VIO and treble gets WHT, YEL, VIO/WHT, left to right with the pots seen from the back, lugs up.
  6. Output and power. Module GRN to the jack tip and BLK to the jack sleeve. Module RED to battery +. Wire the two 9V batteries in series (− of one to + of the other) and run the free battery − to the jack ring, so plugging in turns the preamp on.
  7. Test. Plug in at low volume and tap each pickup's pole pieces with a screwdriver. Turn each knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • One pickup: leave out the blend and wire the pickup straight to volume lug 3.

Aguilar OBP-2 with two volume controls

Same as the blend version, but each pickup gets its own volume. The two volume outputs feed the module's BLU input together.

You need: OBP-2 module and parts as above, 2 volume pots in place of the blend and master volume.

Aguilar OBP-2 with two volume controlsSame as the blend version, but each pickup gets its own volume. The two volume outputs feed the module's BLU input together. Wire numbers match the wire table.1234567891011121314Neck pickupHotGroundBridge pickupHotGroundNeck volumeMiddle lug (in)Right lug (out)Left lugBridge volumeMiddle lug (in)Right lug (out)Left lugBass + treble pots50K linear6 lugs (table)OBP-2 moduleBLU (input)GRN (output)BLK (ground)RED (+ power)EQ wires (6)Stereo jackTipRingSleeve (ground)2 x 9V in series+ (18V)−Ground: pot casings, jack sleeve and cavity shielding, all joined
Aguilar OBP-2 with two volume controls, redrawn as a connection diagram. Original drawing: Aguilar OBP-2 wiring diagram (4 pages), page 4.
Aguilar OBP-2 with two volume controls: wire by wire
#FromToNotes
1Neck pickup: HotNeck volume: Middle lug (in)
2Bridge pickup: HotBridge volume: Middle lug (in)
3Neck pickup: GroundGround (back of a pot casing)
4Bridge pickup: GroundGround (back of a pot casing)
5Neck volume: Right lug (out)OBP-2 module: BLU (input)
6Bridge volume: Right lug (out)OBP-2 module: BLU (input)Both right lugs joined
7Neck volume: Left lugGround (back of a pot casing)
8Bridge volume: Left lugGround (back of a pot casing)
9OBP-2 module: GRN (output)Stereo jack: TipPreamp output
10OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)Module ground
11Stereo jack: Sleeve (ground)Ground (cavity / pot casings)
12OBP-2 module: RED (+ power)2 x 9V in series: + (18V)
132 x 9V in series: −Stereo jack: RingPlugging in turns the preamp on
14Bass + treble pots: 6 lugs (table)OBP-2 module: EQ wires (6)See the EQ table
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Bass 50K linearBRNGRYVIO
Treble 50K linearWHTYELVIO/WHT

Step by step

  1. Pickups to the volumes. Neck pickup hot to the middle lug of the neck volume, bridge pickup hot to the middle lug of the bridge volume. Pickup grounds to a pot casing.
  2. Volume outputs. Join the right lugs of both volumes (seen from the back) and run them to the module's BLU wire. Both left lugs go to ground.
  3. EQ pots. Solder the module's six EQ wires to the bass and treble pots exactly as in the table: bass gets BRN, GRY, VIO and treble gets WHT, YEL, VIO/WHT, left to right with the pots seen from the back, lugs up.
  4. Output and power. Module GRN to the jack tip and BLK to the jack sleeve. Module RED to battery +. Wire the two 9V batteries in series (− of one to + of the other) and run the free battery − to the jack ring, so plugging in turns the preamp on.
  5. Test. Plug in at low volume and tap each pickup's pole pieces with a screwdriver. Turn each knob end to end before closing the cavity.
  • Volume values depend on the pickups: use what the pickup maker recommends.

Aguilar OBP-2 with blend, volume and bypass switch

Adds a DPDT on-on switch that sends either the preamp output or the plain passive signal to the jack tip.

You need: Parts as in the blend version, DPDT on-on mini switch for bypass.

Bypass switch, by function
Switch positionWhat reaches the jack tip
ActiveModule output (GRN)
Passive (bypass)The volume output directly, skipping the module

Step by step

  1. Wire the blend version. Wire everything as in the blend and volume diagram above, but don't connect GRN to the jack tip.
  2. Add the bypass switch. Run the module output (GRN), the volume output and the jack tip to the DPDT bypass switch as Aguilar draws it on page 2, so the switch picks which one feeds the tip.
  3. Test. Plug in at low volume and tap each pickup's pole pieces with a screwdriver. Turn each knob end to end before closing the cavity.
  • Follow Aguilar's page 2 drawing (shown above) for the switch lugs. This text gives the function only.

Aguilar OBP-2 with blend, volume and a stacked bass/treble pot

For a 3-knob layout: bass and treble share one dual 50K linear stacked pot, next to the blend and volume.

You need: Dual 50K linear stacked pot (bass and treble), other parts as in the blend version.

Stacked bass/treble pot (dual 50K linear)
GangLeft lugMiddle lugRight lug
Bass gangBRNGRYVIO
Treble gangWHTYELVIO/WHT

Step by step

  1. Wire the stack. Put the bass wires on the bass gang and the treble wires on the treble gang, in the same left, middle, right order as the single pots.
  2. Everything else. Blend, volume, batteries and jack are wired as in the blend version above.
  3. Test. Plug in at low volume and tap each pickup's pole pieces with a screwdriver. Turn each knob end to end before closing the cavity.

Aguilar OBP-2 with one pickup: volume, treble, bass

One pickup into a volume pot, then the OBP-2 with separate treble and bass pots, two 9V batteries and a stereo jack. Best Bass Gear's own drawing.

You need: OBP-2 module, 2 pots 50K linear (bass, treble), volume pot, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with one pickup: volume, treble, bassOne pickup into a volume pot, then the OBP-2 with separate treble and bass pots, two 9V batteries and a stereo jack. Best Bass Gear's own drawing. Wire numbers match the wire table.1234567891011PickupHotGroundVolumeMiddle lugRight lugLeft lugBass + treble pots50K linear6 lugs (table)OBP-2 moduleBLU (input)GRN (output)BLK (ground)RED (+ power)EQ wires (6)Stereo jackTipRingSleeve (ground)2 x 9V in series+ (18V)−Ground: pot casings, jack sleeve and cavity shielding, all joined
Aguilar OBP-2 with one pickup: volume, treble, bass, redrawn as a connection diagram. Original drawing: OBP-2 volume, treble, bass, page 1.
Aguilar OBP-2 with one pickup: volume, treble, bass: wire by wire
#FromToNotes
1Pickup: HotVolume: Middle lug
2Pickup: GroundGround (back of a pot casing)Back of the volume pot
3Volume: Left lugGround (back of a pot casing)Jumper to the volume casing
4Volume: Right lugOBP-2 module: BLU (input)
5Volume casingStereo jack: Sleeve (ground)
6OBP-2 module: GRN (output)Stereo jack: TipPreamp output
7OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)Module ground
8Stereo jack: Sleeve (ground)Ground (cavity / pot casings)
9OBP-2 module: RED (+ power)2 x 9V in series: + (18V)
102 x 9V in series: −Stereo jack: RingPlugging in turns the preamp on
11Bass + treble pots: 6 lugs (table)OBP-2 module: EQ wires (6)See the EQ table
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Bass 50K linearBRNGRYVIO
Treble 50K linearWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the volume, treble and bass pots and the stereo jack.
  2. Pickup to the volume. Pickup hot to the volume's middle lug. Pickup ground to the back of the volume pot. Jumper the volume's left lug to its casing, and run a wire from the casing to the jack sleeve.
  3. Volume to the module. Volume right lug to the module's BLU wire.
  4. EQ pots. Solder the module's six EQ wires to the bass and treble pots exactly as in the table: bass gets BRN, GRY, VIO and treble gets WHT, YEL, VIO/WHT, left to right with the pots seen from the back, lugs up.
  5. Output and power. Module GRN to the jack tip and BLK to the jack sleeve. Module RED to battery +. Wire the two 9V batteries in series (− of one to + of the other) and run the free battery − to the jack ring, so plugging in turns the preamp on.
  6. Test. Plug in at low volume and tap each pickup's pole pieces with a screwdriver. Turn each knob end to end before closing the cavity.
  • Lug positions are as drawn on Best Bass Gear's sheet (pots from the back, lugs up).
  • The jack sleeve also goes to cavity ground (shielding).

Aguilar OBP-2 with one pickup: volume and stacked treble/bass

A 2-knob layout: one pickup into a volume, and the OBP-2's treble and bass on one stacked pot.

You need: OBP-2 module, dual 50K linear stacked pot (treble/bass), volume pot, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with one pickup: volume and stacked treble/bassA 2-knob layout: one pickup into a volume, and the OBP-2's treble and bass on one stacked pot. Wire numbers match the wire table.1234567891011PickupHotGroundVolumeMiddle lugRight lugLeft lugTreble/bass stackdual 50K linear6 lugs (table)OBP-2 moduleBLU (input)GRN (output)BLK (ground)RED (+ power)EQ wires (6)Stereo jackTipRingSleeve (ground)2 x 9V in series+ (18V)−Ground: pot casings, jack sleeve and cavity shielding, all joined
Aguilar OBP-2 with one pickup: volume and stacked treble/bass, redrawn as a connection diagram. Original drawing: OBP-2 volume, treble/bass stack, page 1.
Aguilar OBP-2 with one pickup: volume and stacked treble/bass: wire by wire
#FromToNotes
1Pickup: HotVolume: Middle lug
2Pickup: GroundGround (back of a pot casing)Back of the volume pot
3Volume: Left lugGround (back of a pot casing)Jumper to the volume casing
4Volume: Right lugOBP-2 module: BLU (input)
5Volume casingStereo jack: Sleeve (ground)
6OBP-2 module: GRN (output)Stereo jack: TipPreamp output
7OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)Module ground
8Stereo jack: Sleeve (ground)Ground (cavity / pot casings)
9OBP-2 module: RED (+ power)2 x 9V in series: + (18V)
102 x 9V in series: −Stereo jack: RingPlugging in turns the preamp on
11Treble/bass stack: 6 lugs (table)OBP-2 module: EQ wires (6)See the stack table
Treble/bass stack: which module wire goes on which lug (seen from the back, lugs up)
GangLeft lugMiddle lugRight lug
Bass (rear gang)BRNGRYVIO
Treble (front gang)WHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the volume, the stacked treble/bass pot and the stereo jack.
  2. Pickup to the volume. Pickup hot to the volume's middle lug, ground to the back of the volume pot. Jumper the volume's left lug to its casing, and run the casing to the jack sleeve.
  3. Volume to the module. Volume right lug to the module's BLU wire.
  4. Stacked pot. BRN, GRY, VIO on the bass gang and WHT, YEL, VIO/WHT on the treble gang, left to right as in the table.
  5. Output and power. Module GRN to the jack tip and BLK to the jack sleeve. Module RED to battery +. Wire the two 9V batteries in series (− of one to + of the other) and run the free battery − to the jack ring, so plugging in turns the preamp on.
  6. Test. Plug in at low volume and tap each pickup's pole pieces with a screwdriver. Turn each knob end to end before closing the cavity.
  • Lug positions are as drawn on Best Bass Gear's sheet.

Aguilar OBP-2: volume, volume, treble, bass with active/passive switch

Two pickups on two volumes, separate treble and bass, and a DPDT active/passive switch that bypasses the preamp. Best Bass Gear's own drawing.

You need: OBP-2 module, 2 pots 50K linear (bass, treble), 2 volume pots, DPDT on-on mini switch, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2: volume, volume, treble, bass with active/passive switchTwo pickups on two volumes, separate treble and bass, and a DPDT active/passive switch that bypasses the preamp. Best Bass Gear's own drawing. Wire numbers match the wire table.123456789101112131415161718Pickup 1HotGroundPickup 2HotGroundVolume 1Middle lugRight lugLeft lugVolume 2Middle lugRight lugLeft lugA/P switchDPDT on-onLeft end ALeft middleLeft end BRight end ARight middleRight end BBass + treble pots50K linear6 lugs (table)OBP-2 moduleBLU (input)GRN (output)BLK (ground)RED (+ power)EQ wires (6)Stereo jackTipRingSleeve (ground)2 x 9V in series+ (18V)−Ground: pot casings, jack sleeve and cavity shielding, all joined
Aguilar OBP-2: volume, volume, treble, bass with active/passive switch, redrawn as a connection diagram. Original drawing: OBP-2 volume, volume, treble, bass, active/passive switch, page 1.
Aguilar OBP-2: volume, volume, treble, bass with active/passive switch: wire by wire
#FromToNotes
1Pickup 1: HotVolume 1: Middle lug
2Pickup 2: HotVolume 2: Middle lug
3Pickup 1 + 2: GroundGround (back of a pot casing)Back of a volume pot
4Volume 1: Left lugGround (back of a pot casing)Jumper to its casing
5Volume 2: Left lugGround (back of a pot casing)Jumper to its casing
6Volume 1: Right lugVolume 2: Right lugOutputs joined
7Volume 2: Right lugA/P switch: Left end A
8OBP-2 module: BLU (input)A/P switch: Left middle
9A/P switch: Left end BStereo jack: Sleeve (ground)
10OBP-2 module: GRN (output)A/P switch: Right end A
11A/P switch: Right middleStereo jack: Tip
12A/P switch: Right end BA/P switch: Left end AJumper
13Volume casingsStereo jack: Sleeve (ground)
14OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)Module ground
15Stereo jack: Sleeve (ground)Ground (cavity / pot casings)
16OBP-2 module: RED (+ power)2 x 9V in series: + (18V)
172 x 9V in series: −Stereo jack: RingPlugging in turns the preamp on
18Bass + treble pots: 6 lugs (table)OBP-2 module: EQ wires (6)See the EQ table
Active/passive switch (DPDT on-on), lug by lug as drawn
Switch lugLeft columnRight column
End AVolume outputs (joined right lugs)Module GRN (output)
Middle (common)Module BLU (input)Jack tip
End BGround (jack sleeve)Jumper to left column end A (volume outputs)
What the switch does
PositionModule input (BLU)Jack tip gets
Active (toward end A)Volume outputsModule GRN (preamp on)
Passive (toward end B)Grounded, so the idle preamp stays quietVolume outputs directly
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Bass 50K linearBRNGRYVIO
Treble 50K linearWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit both volumes, the treble and bass pots, the switch and the stereo jack.
  2. Pickups to the volumes. Pickup 1 hot to volume 1's middle lug, pickup 2 hot to volume 2's middle lug. Pickup grounds to the back of a volume pot. Jumper each volume's left lug to its own casing and join the casings.
  3. Volume outputs. Join the right lugs of both volumes and run them to the switch's left end A lug.
  4. Switch. Module BLU to the left middle lug, ground to the left end B lug. Module GRN to the right end A lug, the jack tip to the right middle lug, and jumper the right end B lug to the left end A lug.
  5. EQ pots. Solder the module's six EQ wires to the bass and treble pots exactly as in the table: bass gets BRN, GRY, VIO and treble gets WHT, YEL, VIO/WHT, left to right with the pots seen from the back, lugs up.
  6. Output and power. Module BLK and the volume casings to the jack sleeve. Module RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring.
  7. Test. Plug in at low volume and tap each pickup's pole pieces with a screwdriver. Turn each knob end to end before closing the cavity.
  • In passive the preamp input is grounded and the volumes go straight to the jack, so the bass still plays with a dead battery.
  • End A and end B are the two outer rows of the switch as drawn. Check with a meter which way the lever connects them before you solder.

Aguilar OBP-2: volume (push/pull active/passive), blend, treble, bass

Two pickups into a dual-gang blend, a volume with a push/pull switch for active/passive, and separate treble and bass. Best Bass Gear's own drawing.

You need: OBP-2 module, 2 pots 50K linear (bass, treble), dual blend pot, push/pull volume pot (DPDT), 2 x 9V batteries, stereo output jack.

Aguilar OBP-2: volume (push/pull active/passive), blend, treble, bassTwo pickups into a dual-gang blend, a volume with a push/pull switch for active/passive, and separate treble and bass. Best Bass Gear's own drawing. Wire numbers match the wire table.1234567891011121314151617Bridge pickupHotGroundNeck pickupHotGroundBlenddual gangRear gang middleFront gang middleRear left + front rightRear right + front leftPush/pull volumepot + DPDTRight lug (in)Middle lug (wiper)Left lugSw left end ASw left middleSw left end BSw right end ASw right middleSw right end BBass + treble pots50K linear6 lugs (table)OBP-2 moduleBLU (input)GRN (output)BLK (ground)RED (+ power)EQ wires (6)Stereo jackTipRingSleeve (ground)2 x 9V in series+ (18V)−Ground: pot casings, jack sleeve and cavity shielding, all joined
Aguilar OBP-2: volume (push/pull active/passive), blend, treble, bass, redrawn as a connection diagram. Original drawing: OBP-2 volume (push/pull active/passive), blend, treble, bass, page 1.
Aguilar OBP-2: volume (push/pull active/passive), blend, treble, bass: wire by wire
#FromToNotes
1Bridge pickup: HotBlend: Rear gang middle
2Neck pickup: HotBlend: Front gang middle
3Bridge + neck pickup: GroundGround (back of a pot casing)Back of the volume pot
4Blend: Rear left + front rightPush/pull volume: Right lug (in)Blend output (the two lugs are joined)
5Blend: Rear right + front leftStereo jack: Sleeve (ground)Blend ground (the two lugs are joined)
6Push/pull volume: Left lugPush/pull volume: Sw left end A
7Push/pull volume: Sw left end AGround (back of a pot casing)Volume casing
8Push/pull volume: Middle lug (wiper)Push/pull volume: Sw right end A
9Push/pull volume: Sw right end APush/pull volume: Sw left end BJumper
10OBP-2 module: BLU (input)Push/pull volume: Sw left middle
11Push/pull volume: Sw right middleStereo jack: Tip
12OBP-2 module: GRN (output)Push/pull volume: Sw right end B
13OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)Module ground
14Stereo jack: Sleeve (ground)Ground (cavity / pot casings)
15OBP-2 module: RED (+ power)2 x 9V in series: + (18V)
162 x 9V in series: −Stereo jack: RingPlugging in turns the preamp on
17Bass + treble pots: 6 lugs (table)OBP-2 module: EQ wires (6)See the EQ table
Push/pull volume: switch lugs as drawn (DPDT on the back of the pot)
Switch lugLeft columnRight column
End AVolume left lug + ground (pot casing)Volume middle lug (wiper)
Middle (common)Module BLU (input)Jack tip
End BJumper to right column end A (volume wiper)Module GRN (output)
What the push/pull does
PositionModule input (BLU)Jack tip gets
Toward end B (active)Volume wiperModule GRN (preamp on)
Toward end A (passive)GroundedVolume wiper directly
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Bass 50K linearBRNGRYVIO
Treble 50K linearWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the blend, the push/pull volume, the treble and bass pots and the stereo jack.
  2. Pickups to the blend. Bridge pickup hot to the middle lug of the rear gang, neck pickup hot to the middle lug of the front gang. Pickup grounds to the back of the volume pot.
  3. Blend lugs. Join the rear gang's left lug to the front gang's right lug: that is the blend output, and it goes to the volume's right lug. Join the rear gang's right lug to the front gang's left lug and run it to ground (jack sleeve).
  4. Volume and switch. Volume left lug to the switch's left end A lug, which also goes to the pot casing (ground). Volume middle lug to the right end A lug, and jumper right end A to left end B.
  5. Switch to the module and jack. Module BLU to the left middle lug, the jack tip to the right middle lug, module GRN to the right end B lug.
  6. EQ pots. Solder the module's six EQ wires to the bass and treble pots exactly as in the table: bass gets BRN, GRY, VIO and treble gets WHT, YEL, VIO/WHT, left to right with the pots seen from the back, lugs up.
  7. Output and power. Module BLK to the jack sleeve. Module RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring.
  8. Test. Plug in at low volume and tap each pickup's pole pieces with a screwdriver. Turn each knob end to end before closing the cavity.
  • Passive grounds the preamp input and sends the volume straight to the jack, so the bass plays with a dead battery.
  • Which way (push or pull) is active depends on the switch: check with a meter before you close up.

Aguilar OBP-2 with stacked volumes and stacked bass/treble

Two pickups on a volume/volume stack and the OBP-2's bass and treble on a second stack: two knobs that fit a two-hole control plate. The drawing labels the box OBP3 Module, but the wiring is the OBP-2's.

You need: OBP-2 module, dual 50K linear treble/bass stack, dual concentric volume pot (value to suit the pickups), 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with stacked volumes and stacked bass/treble: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with stacked volumes and stacked bass/treble: connection diagramPickup 1Pickup 2Volume stackvol/vol, outputs joinedOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveout → BLUGRN → tipTreble/bass stackRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with stacked volumes and stacked bass/treble, redrawn as a connection diagram.
Aguilar OBP-2 with stacked volumes and stacked bass/treble: wire by wire
#FromToNotes
1Pickup 1: HotVolume stack, upper deck: Middle lug
2Pickup 2: HotVolume stack, lower deck: Middle lug
3Both pickups: GroundGround (back of the volume pot)
4Upper deck: Right lugLower deck: Right lugJoined: this is the output
5Upper and lower deck: Left lugsPot casingJumpered to ground
6Volume stack: Right lugs (joined)OBP-2 module: BLU (input)
7OBP-2 module: GRN (output)Stereo jack: TipPreamp output
8OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
9OBP-2 module: 6 EQ wiresTreble/bass stackSee the EQ table
10OBP-2 module: RED (+)First battery +
11First battery −Second battery +Two 9V in series (18V)
12Second battery −Stereo jack: RingPlugging in powers the preamp
13Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Treble/bass stack, bass deck (dual 50K linear)BRNGRYVIO
Treble/bass stack, treble deckWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots and the stereo jack. Join the pot casings with a bare wire.
  2. Pickups to the stacked volume. Pickup 1 hot to the middle lug of one deck, pickup 2 hot to the middle lug of the other. Join the two right lugs: that is the output. Jumper both left lugs to the casing. Pickup grounds to the back of the pot.
  3. Volume to the module. Volume stack Right lugs (joined) to the module's BLU wire.
  4. EQ stack. Solder the module's six EQ wires to the stacked pot as in the EQ table: one deck gets BRN, GRY, VIO, the other WHT, YEL, VIO/WHT.
  5. Output and power. Module GRN to the jack tip. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  6. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Aguilar OBP-2 with blend, volume, stacked bass/treble and A/P switch

Blend and volume, the OBP-2's bass and treble on one stacked pot, and a mini switch for active/passive. Three knobs and a switch.

You need: OBP-2 module, dual 50K linear treble/bass stack, dual-audio blend pot, volume pot (value to suit the pickups), DPDT on-on mini switch for active/passive, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with blend, volume, stacked bass/treble and A/P switch: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with blend, volume, stacked bass/treble and A/P switch: connection diagramNeck pickupBridge pickupBlend + volumepickup grounds hereOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveA/P switchDPDT on-onBLUGRNtip (active or passive)Treble/bass stackRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with blend, volume, stacked bass/treble and A/P switch, redrawn as a connection diagram.
Aguilar OBP-2 with blend, volume, stacked bass/treble and A/P switch: wire by wire
#FromToNotes
1Bridge pickup: HotBlend: middle lug of one gang
2Neck pickup: HotBlend: middle lug of the other gang
3Both pickups: GroundGround (back of the volume pot)
4Blend: output lugs (one outer lug per gang, joined)Volume: Right lug
5Blend: ground lugs (the other outer lug per gang, joined)Ground (back of the volume pot)
6Volume: Left lugVolume casingJumper to ground
7Volume: Middle lugA/P switch: top-left lugPassive signal
8OBP-2 module: BLU (input)A/P switch: middle-left lugCommon, pole 1
9A/P switch: bottom-left lugGroundGrounds the preamp input in passive
10OBP-2 module: GRN (output)A/P switch: top-right lug
11A/P switch: middle-right lugStereo jack: TipCommon, pole 2
12A/P switch: bottom-right lugA/P switch: top-left lugJumper: passive signal to the tip
13OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
14OBP-2 module: 6 EQ wiresTreble/bass stackSee the EQ table
15OBP-2 module: RED (+)First battery +
16First battery −Second battery +Two 9V in series (18V)
17Second battery −Stereo jack: RingPlugging in powers the preamp
18Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Treble/bass stack, bass deck (dual 50K linear)BRNGRYVIO
Treble/bass stack, treble deckWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots, the mini switch and the stereo jack. Join the pot casings with a bare wire.
  2. Pickups to the blend and volume. Bridge hot to the middle lug of one blend gang, neck hot to the middle lug of the other. Join one outer lug of each gang and run it to the volume's right lug; join the other two outer lugs to ground. Volume left lug to its casing. Pickup grounds go to the back of the volume pot.
  3. Active/passive switch. Volume output to the top-left lug, module BLU to middle-left, bottom-left to ground. Module GRN to top-right, middle-right to the jack tip, and a jumper from bottom-right to top-left. Active: the signal runs through the preamp. Passive: the preamp input is grounded and the volume output goes straight to the tip.
  4. EQ stack. Solder the module's six EQ wires to the stacked pot as in the EQ table: one deck gets BRN, GRY, VIO, the other WHT, YEL, VIO/WHT.
  5. Output and power. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  6. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Aguilar OBP-2 with one pickup: volume, treble, bass and A/P switch

One pickup, a volume, separate treble and bass, and a mini switch to bypass the preamp.

You need: OBP-2 module, 2 pots 50K linear: bass, treble, volume pot (value to suit the pickup), DPDT on-on mini switch for active/passive, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with one pickup: volume, treble, bass and A/P switch: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with one pickup: volume, treble, bass and A/P switch: connection diagramPickupVolumepickup ground hereOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveA/P switchDPDT on-onBLUGRNtip (active or passive)BassTrebleRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with one pickup: volume, treble, bass and A/P switch, redrawn as a connection diagram.
Aguilar OBP-2 with one pickup: volume, treble, bass and A/P switch: wire by wire
#FromToNotes
1Pickup: HotVolume: Middle lug
2Pickup: GroundGround (back of the volume pot)
3Volume: Left lugVolume casingJumper to ground
4Volume: Right lugA/P switch: top-left lugPassive signal
5OBP-2 module: BLU (input)A/P switch: middle-left lugCommon, pole 1
6A/P switch: bottom-left lugGroundGrounds the preamp input in passive
7OBP-2 module: GRN (output)A/P switch: top-right lug
8A/P switch: middle-right lugStereo jack: TipCommon, pole 2
9A/P switch: bottom-right lugA/P switch: top-left lugJumper: passive signal to the tip
10OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
11OBP-2 module: 6 EQ wiresBass and treble potsSee the EQ table
12OBP-2 module: RED (+)First battery +
13First battery −Second battery +Two 9V in series (18V)
14Second battery −Stereo jack: RingPlugging in powers the preamp
15Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Bass 50K linearBRNGRYVIO
Treble 50K linearWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots, the mini switch and the stereo jack. Join the pot casings with a bare wire.
  2. Pickup to the volume. Pickup hot to the volume's middle lug and pickup ground to the back of the pot. Jumper the left lug to the casing. In this drawing the right lug is the output.
  3. Active/passive switch. Volume output to the top-left lug, module BLU to middle-left, bottom-left to ground. Module GRN to top-right, middle-right to the jack tip, and a jumper from bottom-right to top-left. Active: the signal runs through the preamp. Passive: the preamp input is grounded and the volume output goes straight to the tip.
  4. EQ pots. Bass pot gets BRN, GRY, VIO and treble gets WHT, YEL, VIO/WHT, left to right with the pots seen from the back, lugs up.
  5. Output and power. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  6. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Aguilar OBP-2 with two volumes and stacked bass/treble

A volume for each pickup and the bass and treble on one stacked pot: three knobs for a J-style control plate.

You need: OBP-2 module, dual 50K linear treble/bass stack, 2 volume pots (value to suit the pickups), 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with two volumes and stacked bass/treble: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with two volumes and stacked bass/treble: connection diagramPickup 1Pickup 2Volume 1 + 2outputs joinedOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveout → BLUGRN → tipTreble/bass stackRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with two volumes and stacked bass/treble, redrawn as a connection diagram.
Aguilar OBP-2 with two volumes and stacked bass/treble: wire by wire
#FromToNotes
1Pickup 1: HotVolume 1: Middle lug
2Pickup 2: HotVolume 2: Middle lug
3Both pickups: GroundGround (back of the volume pot)
4Volume 1: Right lugVolume 2: Right lugJoined: this is the output
5Volume 1 and 2: Left lugsTheir own casingsJumpered; casings joined to ground
6Both volumes: Right lugs (joined)OBP-2 module: BLU (input)
7OBP-2 module: GRN (output)Stereo jack: TipPreamp output
8OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
9OBP-2 module: 6 EQ wiresTreble/bass stackSee the EQ table
10OBP-2 module: RED (+)First battery +
11First battery −Second battery +Two 9V in series (18V)
12Second battery −Stereo jack: RingPlugging in powers the preamp
13Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Treble/bass stack, bass deck (dual 50K linear)BRNGRYVIO
Treble/bass stack, treble deckWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots and the stereo jack. Join the pot casings with a bare wire.
  2. Pickups to the volumes. Pickup 1 hot to the middle lug of volume 1, pickup 2 hot to the middle lug of volume 2. Join the two right lugs: that pair is the output. Jumper each left lug to its casing and join the casings. Pickup grounds to the back of a volume pot.
  3. Volume to the module. Both volumes right lugs (joined) to the module's BLU wire.
  4. EQ stack. Solder the module's six EQ wires to the stacked pot as in the EQ table: one deck gets BRN, GRY, VIO, the other WHT, YEL, VIO/WHT.
  5. Output and power. Module GRN to the jack tip. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  6. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Aguilar OBP-2 with two volumes, stacked bass/treble and A/P switch

Two volumes, stacked bass/treble and a mini switch for active/passive.

You need: OBP-2 module, dual 50K linear treble/bass stack, 2 volume pots (value to suit the pickups), DPDT on-on mini switch for active/passive, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with two volumes, stacked bass/treble and A/P switch: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with two volumes, stacked bass/treble and A/P switch: connection diagramPickup 1Pickup 2Volume 1 + 2outputs joinedOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveA/P switchDPDT on-onBLUGRNtip (active or passive)Treble/bass stackRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with two volumes, stacked bass/treble and A/P switch, redrawn as a connection diagram.
Aguilar OBP-2 with two volumes, stacked bass/treble and A/P switch: wire by wire
#FromToNotes
1Pickup 1: HotVolume 1: Middle lug
2Pickup 2: HotVolume 2: Middle lug
3Both pickups: GroundGround (back of the volume pot)
4Volume 1: Right lugVolume 2: Right lugJoined: this is the output
5Volume 1 and 2: Left lugsTheir own casingsJumpered; casings joined to ground
6Both volumes: Right lugs (joined)A/P switch: top-left lugPassive signal
7OBP-2 module: BLU (input)A/P switch: middle-left lugCommon, pole 1
8A/P switch: bottom-left lugGroundGrounds the preamp input in passive
9OBP-2 module: GRN (output)A/P switch: top-right lug
10A/P switch: middle-right lugStereo jack: TipCommon, pole 2
11A/P switch: bottom-right lugA/P switch: top-left lugJumper: passive signal to the tip
12OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
13OBP-2 module: 6 EQ wiresTreble/bass stackSee the EQ table
14OBP-2 module: RED (+)First battery +
15First battery −Second battery +Two 9V in series (18V)
16Second battery −Stereo jack: RingPlugging in powers the preamp
17Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Treble/bass stack, bass deck (dual 50K linear)BRNGRYVIO
Treble/bass stack, treble deckWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots, the mini switch and the stereo jack. Join the pot casings with a bare wire.
  2. Pickups to the volumes. Pickup 1 hot to the middle lug of volume 1, pickup 2 hot to the middle lug of volume 2. Join the two right lugs: that pair is the output. Jumper each left lug to its casing and join the casings. Pickup grounds to the back of a volume pot.
  3. Active/passive switch. Volume output to the top-left lug, module BLU to middle-left, bottom-left to ground. Module GRN to top-right, middle-right to the jack tip, and a jumper from bottom-right to top-left. Active: the signal runs through the preamp. Passive: the preamp input is grounded and the volume output goes straight to the tip.
  4. EQ stack. Solder the module's six EQ wires to the stacked pot as in the EQ table: one deck gets BRN, GRY, VIO, the other WHT, YEL, VIO/WHT.
  5. Output and power. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  6. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Aguilar OBP-2 with push-pull A/P volume, blend and stacked bass/treble

Three knobs: a volume that pulls up for passive, a blend, and stacked bass/treble.

You need: OBP-2 module, dual 50K linear treble/bass stack, dual-audio blend pot, push-pull volume pot (DPDT) for active/passive, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with push-pull A/P volume, blend and stacked bass/treble: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with push-pull A/P volume, blend and stacked bass/treble: connection diagramNeck pickupBridge pickupBlend + PP volumepush-pull A/P on volumeOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveA/P (push-pull)switch on volume potBLUGRNtip (active or passive)Treble/bass stackRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with push-pull A/P volume, blend and stacked bass/treble, redrawn as a connection diagram.
Aguilar OBP-2 with push-pull A/P volume, blend and stacked bass/treble: wire by wire
#FromToNotes
1Bridge pickup: HotBlend: middle lug of one gang
2Neck pickup: HotBlend: middle lug of the other gang
3Both pickups: GroundGround (back of the volume pot)
4Blend: output lugs (joined)Volume: Right lug
5Blend: ground lugs (joined)Ground (back of the volume pot)
6Volume: Left lugVolume casingJumper to ground
7Volume: Middle lugVolume switch: top-right lugPassive signal
8OBP-2 module: BLU (input)Volume switch: middle-left lugCommon, pole 1
9Volume switch: top-left lugGroundGrounds the preamp input in passive
10Volume switch: bottom-left lugVolume switch: top-right lugJumper
11Volume switch: middle-right lugStereo jack: TipCommon, pole 2
12OBP-2 module: GRN (output)Volume switch: bottom-right lug
13OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
14OBP-2 module: 6 EQ wiresTreble/bass stackSee the EQ table
15OBP-2 module: RED (+)First battery +
16First battery −Second battery +Two 9V in series (18V)
17Second battery −Stereo jack: RingPlugging in powers the preamp
18Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Treble/bass stack, bass deck (dual 50K linear)BRNGRYVIO
Treble/bass stack, treble deckWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots and the stereo jack. Join the pot casings with a bare wire.
  2. Pickups to the blend and volume. Bridge hot to the middle lug of one blend gang, neck hot to the middle lug of the other. Join one outer lug of each gang and run it to the volume's right lug; join the other two to ground. Volume left lug to the casing. Pickup grounds go to the back of the volume pot.
  3. Push-pull active/passive. On the volume pot's switch: volume output to top-right, module BLU to middle-left, top-left to ground, and a jumper from bottom-left to top-right. Middle-right to the jack tip, module GRN to bottom-right. Pushed down, the preamp is on; pulled up, it is bypassed. If your pot works the other way round, swap the top and bottom wires on both sides.
  4. EQ stack. Solder the module's six EQ wires to the stacked pot as in the EQ table: one deck gets BRN, GRY, VIO, the other WHT, YEL, VIO/WHT.
  5. Output and power. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  6. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Aguilar OBP-2 with push-pull A/P volume, second volume and stacked bass/treble

Two volumes (the first pulls up for passive) and stacked bass/treble: a three-knob J-style layout with no extra switch.

You need: OBP-2 module, dual 50K linear treble/bass stack, push-pull volume pot (DPDT) for active/passive, second volume pot, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with push-pull A/P volume, second volume and stacked bass/treble: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with push-pull A/P volume, second volume and stacked bass/treble: connection diagramPickup 1Pickup 2PP vol + volumeoutputs joinedOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveA/P (push-pull)switch on volume potBLUGRNtip (active or passive)Treble/bass stackRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with push-pull A/P volume, second volume and stacked bass/treble, redrawn as a connection diagram.
Aguilar OBP-2 with push-pull A/P volume, second volume and stacked bass/treble: wire by wire
#FromToNotes
1Pickup 1: HotPush-pull volume: Middle lug
2Pickup 2: HotVolume 2: Middle lug
3Both pickups: GroundGround (back of the volume pot)
4Push-pull volume: Right lugVolume 2: Right lugJoined: this is the output
5Both volumes: Left lugsGround (pot casings)
6Both volumes: Right lugs (joined)Volume switch: top-right lugPassive signal
7OBP-2 module: BLU (input)Volume switch: middle-left lugCommon, pole 1
8Volume switch: top-left lugGroundGrounds the preamp input in passive
9Volume switch: bottom-left lugVolume switch: top-right lugJumper
10Volume switch: middle-right lugStereo jack: TipCommon, pole 2
11OBP-2 module: GRN (output)Volume switch: bottom-right lug
12OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
13OBP-2 module: 6 EQ wiresTreble/bass stackSee the EQ table
14OBP-2 module: RED (+)First battery +
15First battery −Second battery +Two 9V in series (18V)
16Second battery −Stereo jack: RingPlugging in powers the preamp
17Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Treble/bass stack, bass deck (dual 50K linear)BRNGRYVIO
Treble/bass stack, treble deckWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots and the stereo jack. Join the pot casings with a bare wire.
  2. Pickups to the volumes. Pickup 1 hot to the middle lug of the push-pull volume, pickup 2 hot to the middle lug of the second volume. Join the two right lugs: that is the output, and it goes to the push-pull switch. Both left lugs to ground; pickup grounds to the back of a volume pot.
  3. Push-pull active/passive. On the volume pot's switch: volume output to top-right, module BLU to middle-left, top-left to ground, and a jumper from bottom-left to top-right. Middle-right to the jack tip, module GRN to bottom-right. Pushed down, the preamp is on; pulled up, it is bypassed. If your pot works the other way round, swap the top and bottom wires on both sides.
  4. EQ stack. Solder the module's six EQ wires to the stacked pot as in the EQ table: one deck gets BRN, GRY, VIO, the other WHT, YEL, VIO/WHT.
  5. Output and power. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  6. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Aguilar OBP-2 with push-pull A/P volume, second volume, stacked bass/treble and passive tone

Two volumes with push-pull active/passive on the first, stacked bass/treble, and a passive tone control.

You need: OBP-2 module, dual 50K linear treble/bass stack, push-pull volume pot (DPDT) for active/passive, second volume pot, tone pot, tone capacitor, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with push-pull A/P volume, second volume, stacked bass/treble and passive tone: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with push-pull A/P volume, second volume, stacked bass/treble and passive tone: connection diagramPickup 1Pickup 2PP vol + volumeoutputs joinedPassive tone250K audio + 0.022 µFOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveA/P (push-pull)switch on volume potBLUGRNtip (active or passive)Treble/bass stackRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with push-pull A/P volume, second volume, stacked bass/treble and passive tone, redrawn as a connection diagram.
Aguilar OBP-2 with push-pull A/P volume, second volume, stacked bass/treble and passive tone: wire by wire
#FromToNotes
1Pickup 1: HotPush-pull volume: Middle lug
2Pickup 2: HotVolume 2: Middle lug
3Both pickups: GroundGround (back of the volume pot)
4Push-pull volume: Right lugVolume 2: Right lugJoined: this is the output
5Both volumes: Left lugsGround (pot casings)
6Tone pot: Outer lugBoth volumes: Right lugs (joined)Passive tone
7Tone: Middle lugCapacitor
8Capacitor: other legStereo jack: Sleeve (ground)
9Both volumes: Right lugs (joined)Volume switch: top-right lugPassive signal
10OBP-2 module: BLU (input)Volume switch: middle-left lugCommon, pole 1
11Volume switch: top-left lugGroundGrounds the preamp input in passive
12Volume switch: bottom-left lugVolume switch: top-right lugJumper
13Volume switch: middle-right lugStereo jack: TipCommon, pole 2
14OBP-2 module: GRN (output)Volume switch: bottom-right lug
15OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
16OBP-2 module: 6 EQ wiresTreble/bass stackSee the EQ table
17OBP-2 module: RED (+)First battery +
18First battery −Second battery +Two 9V in series (18V)
19Second battery −Stereo jack: RingPlugging in powers the preamp
20Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Treble/bass stack, bass deck (dual 50K linear)BRNGRYVIO
Treble/bass stack, treble deckWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots and the stereo jack. Join the pot casings with a bare wire.
  2. Pickups to the volumes. Pickup 1 hot to the middle lug of the push-pull volume, pickup 2 hot to the middle lug of the second volume. Join the two right lugs: that is the output, and it goes to the push-pull switch. Both left lugs to ground; pickup grounds to the back of a volume pot.
  3. Passive tone. One outer lug of the tone pot to the volume output, the middle lug to the capacitor, and the capacitor's other leg to ground. Our drawing gives no values: most passive tone controls use a 250K audio pot and a 0.022 µF to 0.047 µF cap, but go by your pickups.
  4. Push-pull active/passive. On the volume pot's switch: volume output to top-right, module BLU to middle-left, top-left to ground, and a jumper from bottom-left to top-right. Middle-right to the jack tip, module GRN to bottom-right. Pushed down, the preamp is on; pulled up, it is bypassed. If your pot works the other way round, swap the top and bottom wires on both sides.
  5. EQ stack. Solder the module's six EQ wires to the stacked pot as in the EQ table: one deck gets BRN, GRY, VIO, the other WHT, YEL, VIO/WHT.
  6. Output and power. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  7. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Aguilar OBP-2 with one pickup: push-pull A/P volume, treble, bass

One pickup and three knobs: the volume pulls up for passive, with separate treble and bass.

You need: OBP-2 module, 2 pots 50K linear: bass, treble, push-pull volume pot (DPDT) for active/passive, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with one pickup: push-pull A/P volume, treble, bass: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with one pickup: push-pull A/P volume, treble, bass: connection diagramPickupPP volumepush-pull A/P on volumeOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveA/P (push-pull)switch on volume potBLUGRNtip (active or passive)BassTrebleRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with one pickup: push-pull A/P volume, treble, bass, redrawn as a connection diagram.
Aguilar OBP-2 with one pickup: push-pull A/P volume, treble, bass: wire by wire
#FromToNotes
1Pickup: HotVolume: Middle lug
2Pickup: GroundGround (back of the volume pot)
3Volume: Left lugGround (volume casing)
4Volume: Right lugVolume switch: top-right lugPassive signal
5OBP-2 module: BLU (input)Volume switch: middle-left lugCommon, pole 1
6Volume switch: top-left lugGroundGrounds the preamp input in passive
7Volume switch: bottom-left lugVolume switch: top-right lugJumper
8Volume switch: middle-right lugStereo jack: TipCommon, pole 2
9OBP-2 module: GRN (output)Volume switch: bottom-right lug
10OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
11OBP-2 module: 6 EQ wiresBass and treble potsSee the EQ table
12OBP-2 module: RED (+)First battery +
13First battery −Second battery +Two 9V in series (18V)
14Second battery −Stereo jack: RingPlugging in powers the preamp
15Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Bass 50K linearBRNGRYVIO
Treble 50K linearWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots and the stereo jack. Join the pot casings with a bare wire.
  2. Pickup to the volume. Pickup hot to the volume's middle lug, pickup ground to the back of the pot, left lug to ground. In this drawing the right lug is the output, and it goes to the pot's switch.
  3. Push-pull active/passive. On the volume pot's switch: volume output to top-right, module BLU to middle-left, top-left to ground, and a jumper from bottom-left to top-right. Middle-right to the jack tip, module GRN to bottom-right. Pushed down, the preamp is on; pulled up, it is bypassed. If your pot works the other way round, swap the top and bottom wires on both sides.
  4. EQ pots. Bass pot gets BRN, GRY, VIO and treble gets WHT, YEL, VIO/WHT, left to right with the pots seen from the back, lugs up.
  5. Output and power. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  6. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Aguilar OBP-2 with one pickup: push-pull A/P volume and stacked bass/treble

One pickup, two knobs: a push-pull volume for active/passive and a stacked bass/treble.

You need: OBP-2 module, dual 50K linear treble/bass stack, push-pull volume pot (DPDT) for active/passive, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with one pickup: push-pull A/P volume and stacked bass/treble: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with one pickup: push-pull A/P volume and stacked bass/treble: connection diagramPickupPP volumepush-pull A/P on volumeOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveA/P (push-pull)switch on volume potBLUGRNtip (active or passive)Treble/bass stackRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with one pickup: push-pull A/P volume and stacked bass/treble, redrawn as a connection diagram.
Aguilar OBP-2 with one pickup: push-pull A/P volume and stacked bass/treble: wire by wire
#FromToNotes
1Pickup: HotVolume: Middle lug
2Pickup: GroundGround (back of the volume pot)
3Volume: Left lugGround (volume casing)
4Volume: Right lugVolume switch: top-right lugPassive signal
5OBP-2 module: BLU (input)Volume switch: middle-left lugCommon, pole 1
6Volume switch: top-left lugGroundGrounds the preamp input in passive
7Volume switch: bottom-left lugVolume switch: top-right lugJumper
8Volume switch: middle-right lugStereo jack: TipCommon, pole 2
9OBP-2 module: GRN (output)Volume switch: bottom-right lug
10OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
11OBP-2 module: 6 EQ wiresTreble/bass stackSee the EQ table
12OBP-2 module: RED (+)First battery +
13First battery −Second battery +Two 9V in series (18V)
14Second battery −Stereo jack: RingPlugging in powers the preamp
15Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Treble/bass stack, bass deck (dual 50K linear)BRNGRYVIO
Treble/bass stack, treble deckWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots and the stereo jack. Join the pot casings with a bare wire.
  2. Pickup to the volume. Pickup hot to the volume's middle lug, pickup ground to the back of the pot, left lug to ground. In this drawing the right lug is the output, and it goes to the pot's switch.
  3. Push-pull active/passive. On the volume pot's switch: volume output to top-right, module BLU to middle-left, top-left to ground, and a jumper from bottom-left to top-right. Middle-right to the jack tip, module GRN to bottom-right. Pushed down, the preamp is on; pulled up, it is bypassed. If your pot works the other way round, swap the top and bottom wires on both sides.
  4. EQ stack. Solder the module's six EQ wires to the stacked pot as in the EQ table: one deck gets BRN, GRY, VIO, the other WHT, YEL, VIO/WHT.
  5. Output and power. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  6. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Aguilar OBP-2 with volume/tone stack, blend and stacked bass/treble

Three knobs, five controls: a volume/passive-tone stack, a blend, and stacked bass/treble.

You need: OBP-2 module, dual 50K linear treble/bass stack, dual-audio blend pot, volume/tone concentric stack (values to suit the pickups), tone capacitor, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with volume/tone stack, blend and stacked bass/treble: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with volume/tone stack, blend and stacked bass/treble: connection diagramNeck pickupBridge pickupBlend + vol/tonevolume/tone stackPassive tone250K audio + 0.022 µFOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveout → BLUGRN → tipTreble/bass stackRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with volume/tone stack, blend and stacked bass/treble, redrawn as a connection diagram.
Aguilar OBP-2 with volume/tone stack, blend and stacked bass/treble: wire by wire
#FromToNotes
1Bridge pickup: HotBlend: middle lug of one gang
2Neck pickup: HotBlend: middle lug of the other gang
3Both pickups: GroundGround (back of the volume pot)
4Blend: output lugs (joined)Volume deck: Right lug
5Blend: ground lugs (joined)Ground (back of the volume pot)
6Volume deck: Left lugPot casingJumper to ground
7Tone deck of the volume/tone stack: Outer lugVolume deck: Middle lugPassive tone
8Tone: Middle lugCapacitor
9Capacitor: other legStereo jack: Sleeve (ground)
10Volume deck: Middle lugOBP-2 module: BLU (input)
11OBP-2 module: GRN (output)Stereo jack: TipPreamp output
12OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
13OBP-2 module: 6 EQ wiresTreble/bass stackSee the EQ table
14OBP-2 module: RED (+)First battery +
15First battery −Second battery +Two 9V in series (18V)
16Second battery −Stereo jack: RingPlugging in powers the preamp
17Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Treble/bass stack, bass deck (dual 50K linear)BRNGRYVIO
Treble/bass stack, treble deckWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots and the stereo jack. Join the pot casings with a bare wire.
  2. Pickups to the blend and the volume deck. Bridge hot to the middle lug of one blend gang, neck hot to the other. Join one outer lug of each gang to the volume deck's right lug; join the other two to ground. Volume deck left lug to the casing; its middle lug is the output.
  3. Passive tone. One outer lug of the tone pot to the volume output, the middle lug to the capacitor, and the capacitor's other leg to ground. Our drawing gives no values: most passive tone controls use a 250K audio pot and a 0.022 µF to 0.047 µF cap, but go by your pickups.
  4. Volume to the module. Volume deck middle lug to the module's BLU wire.
  5. EQ stack. Solder the module's six EQ wires to the stacked pot as in the EQ table: one deck gets BRN, GRY, VIO, the other WHT, YEL, VIO/WHT.
  6. Output and power. Module GRN to the jack tip. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  7. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • The page shows only the drawing's connections; check the volume/tone stack's lug layout against your pot before soldering.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Aguilar OBP-2 with stacked volumes, passive tone, treble, bass and A/P switch

A volume/volume stack, a passive tone, separate treble and bass, and a mini switch for active/passive.

You need: OBP-2 module, 2 pots 50K linear: bass, treble, dual concentric volume pot (value to suit the pickups), tone pot, tone capacitor, DPDT on-on mini switch for active/passive, 2 x 9V batteries, stereo output jack.

Aguilar OBP-2 with stacked volumes, passive tone, treble, bass and A/P switch: original wiring drawing
Best Bass Gear's drawing, as originally published. Click to enlarge.
Aguilar OBP-2 with stacked volumes, passive tone, treble, bass and A/P switch: connection diagramPickup 1Pickup 2Volume stackvol/vol, outputs joinedPassive tone250K audio + 0.022 µFOBP-2 moduleBLU in · GRN out · BLK · REDStereo jacktip · ring · sleeveA/P switchDPDT on-onBLUGRNtip (active or passive)BassTrebleRED → battery + · two 9V in series · battery − → jack ring · BLK and grounds → jack sleeve
Aguilar OBP-2 with stacked volumes, passive tone, treble, bass and A/P switch, redrawn as a connection diagram.
Aguilar OBP-2 with stacked volumes, passive tone, treble, bass and A/P switch: wire by wire
#FromToNotes
1Pickup 1: HotVolume stack, upper deck: Middle lug
2Pickup 2: HotVolume stack, lower deck: Middle lug
3Both pickups: GroundGround (back of the volume pot)
4Upper deck: Right lugLower deck: Right lugJoined: this is the output
5Upper and lower deck: Left lugsPot casingJumpered to ground
6Tone pot: Outer lugVolume stack: Right lugs (joined)Passive tone
7Tone: Middle lugCapacitor
8Capacitor: other legStereo jack: Sleeve (ground)
9Volume stack: Right lugs (joined)A/P switch: top-left lugPassive signal
10OBP-2 module: BLU (input)A/P switch: middle-left lugCommon, pole 1
11A/P switch: bottom-left lugGroundGrounds the preamp input in passive
12OBP-2 module: GRN (output)A/P switch: top-right lug
13A/P switch: middle-right lugStereo jack: TipCommon, pole 2
14A/P switch: bottom-right lugA/P switch: top-left lugJumper: passive signal to the tip
15OBP-2 module: BLK (ground)Stereo jack: Sleeve (ground)
16OBP-2 module: 6 EQ wiresBass and treble potsSee the EQ table
17OBP-2 module: RED (+)First battery +
18First battery −Second battery +Two 9V in series (18V)
19Second battery −Stereo jack: RingPlugging in powers the preamp
20Stereo jack: SleeveCavity ground / shielding
OBP-2 EQ pots: which module wire goes on which lug (pots seen from the back, lugs up)
PotLeft lugMiddle lugRight lug
Bass 50K linearBRNGRYVIO
Treble 50K linearWHTYELVIO/WHT

Step by step

  1. Mount everything. Fit the pots, the mini switch and the stereo jack. Join the pot casings with a bare wire.
  2. Pickups to the stacked volume. Pickup 1 hot to the middle lug of one deck, pickup 2 hot to the middle lug of the other. Join the two right lugs: that is the output. Jumper both left lugs to the casing. Pickup grounds to the back of the pot.
  3. Passive tone. One outer lug of the tone pot to the volume output, the middle lug to the capacitor, and the capacitor's other leg to ground. Our drawing gives no values: most passive tone controls use a 250K audio pot and a 0.022 µF to 0.047 µF cap, but go by your pickups.
  4. Active/passive switch. Volume output to the top-left lug, module BLU to middle-left, bottom-left to ground. Module GRN to top-right, middle-right to the jack tip, and a jumper from bottom-right to top-left. Active: the signal runs through the preamp. Passive: the preamp input is grounded and the volume output goes straight to the tip.
  5. EQ pots. Bass pot gets BRN, GRY, VIO and treble gets WHT, YEL, VIO/WHT, left to right with the pots seen from the back, lugs up.
  6. Output and power. Module BLK to the jack sleeve and RED to battery +. Wire the two 9V batteries in series and run the free battery − to the jack ring, so plugging in turns the preamp on. Jack sleeve to the cavity shielding.
  7. Test. Plug in at low volume, tap the pickups and turn every knob end to end before closing the cavity.
  • Volume and blend values depend on the pickups: use what the pickup maker recommends.
  • 9V or 18V both work: for one 9V battery, run its − to the jack ring.

Shop Aguilar preamps and custom prewires

Related diagrams

Questions about your install? Email sales@bestbassgear.com.