DiMarzio Model J & Ultra Jazz Wiring Diagram

DiMarzio's install sheet for the Model J and Ultra Jazz pickups (DP123, DP147, DP148, DP149). They drop into U.S. Jazz Basses with no routing. Standard hookup is series humbucking. Add mini switches or push/pull pots for series/parallel (Dual Sound) and phase.

DiMarzio Model J / Ultra Jazz installation instructions and alternative push/pull wiring
DiMarzio Model J / Ultra Jazz installation instructions and alternative push/pull wiring

Download the PDF

Before you solder

  • Neck = pickup 1 to volume pot #1. Bridge = pickup 2 to volume pot #2.
  • Red goes to the center leg of its volume pot. Green goes to the back of the pot (ground).
  • Standard series humbucking: solder black and white together and tape the joint.
  • These pickups are slightly deeper than stock. Remove the foam under the pickups and cut a smaller piece, about 3" x 5/8" (75 x 16 mm), for each one.
  • When removing the old pickups, don't disconnect the other ground wire on the back of volume pot #2.
  • Alternatives on the sheet: two push/pull volumes for Dual Sound, or push/pull volumes plus a phase switch on the tone.
  • Set the height so both pickups are about even at full volume. Adjustable poles can be set in pairs, two per string.

Every diagram, wire by wire

DiMarzio's Model J and Ultra Jazz hookup as text: the standard drop-in wiring and the Dual Sound push/pull option.

How to read these

  • DiMarzio colors: red = hot, green = ground, black and white = the link between the two coils.
  • Neck pickup = pickup 1 on volume pot #1; bridge = pickup 2 on volume pot #2.

DiMarzio Model J / Ultra Jazz: standard series humbucking

Drop-in replacement for U.S. Jazz Bass pickups. Each pickup's red wire goes to the center leg of its volume pot, green to the pot back; black and white are joined and taped. The rest of the stock wiring stays.

You need: DiMarzio DP123, DP147, DP148 or DP149 pickups, the bass's existing volume pots.

DiMarzio Model J / Ultra Jazz: standard series humbuckingDrop-in replacement for U.S. Jazz Bass pickups. Each pickup's red wire goes to the center leg of its volume pot, green to the pot back; black and white are joined and taped. The rest of the stock wiring stays. Wire numbers match the wire table.13Neck pickup (1)Red (hot)GreenBlack + whiteBridge pickup (2)Red (hot)GreenBlack + whiteVolume pot #1existingCenter legVolume pot #2existingCenter leg24Copper lines = signal. Ground symbol = solder to the back of a pot casing (the ground bus). Numbers match the wire table.
DiMarzio Model J / Ultra Jazz: standard series humbucking, redrawn as a connection diagram. Original drawing: DiMarzio Model J / Ultra Jazz installation sheet.
DiMarzio Model J / Ultra Jazz: standard series humbucking: wire by wire
#FromToNotes
1Neck pickup (1): Red (hot)Volume pot #1: Center leg
2Neck pickup (1): GreenGround (back of a pot casing)Back of volume pot #1
3Bridge pickup (2): Red (hot)Volume pot #2: Center leg
4Bridge pickup (2): GreenGround (back of a pot casing)Back of volume pot #2
Black and white wires
PickupWhat to do
Both pickupsSolder black and white together and tape the joint (series humbucking)

Step by step

  1. Remove the old pickups. Loosen the strings, remove the pickguard, turn the control plate over and unsolder the old pickup leads: hot from the center leg, ground from the pot back. Don't disconnect the other ground wire on the back of volume pot #2.
  2. Fit the new pickups. Remove the foam under the pickups (the new ones are deeper) and put a piece about 3" x 5/8" (75 x 16 mm) under each. Run all four wires into the control cavity.
  3. Wire the pickups. Red of each pickup to the center leg of its volume pot (neck = #1, bridge = #2). Green to the back of the same pot. Join black and white and tape them.
  4. Set the height. Restring and set the height so both pickups sound about even at full volume.

DiMarzio Model J / Ultra Jazz: push/pull volumes for Dual Sound (series/parallel)

Replace each volume with a push/pull pot. Its switch toggles that pickup between series (humbucking) and parallel (Dual Sound).

You need: 2 push/pull volume pots (DPDT), DiMarzio Model J or Ultra Jazz pickups.

What each mode joins (per pickup)
ModeHot (to the pot)JoinedGround
Series (humbucking)RedBlack + whiteGreen
Parallel (Dual Sound)Red + white-Green + black
One way to do it on the push/pull switch (DPDT)
PoleCommon lugSeries sideParallel side
Pole AWhiteBlackRed
Pole BBlack(empty)Ground

Step by step

  1. Fit push/pull volumes. Replace both volume pots with push/pull pots of the same value.
  2. Red and green. Red to the pot's center leg, green to the pot back, as in the standard wiring.
  3. Switch. Wire black and white to the push/pull switch as in the table, so one position joins black to white (series) and the other joins white to red and black to ground (parallel).
  4. Test. Plug in at low volume and tap each pickup's pole pieces with a screwdriver. Turn each knob end to end before closing the cavity.
  • DiMarzio's sheet also shows push/pull volumes plus a phase switch on the tone pot. Follow their drawing for that version.

Parts in this diagram

FAQ

Do DiMarzio Model J pickups need routing?

Not in a U.S. Jazz Bass. They're a direct replacement, though you'll need to trim the foam under them.

How do I wire a DiMarzio Model J?

Red to the center leg of the volume pot, green to the back of the pot. Solder black and white together and tape them for standard series humbucking.

Can I get single-coil sounds?

The sheet shows push/pull volume pots for series/parallel (Dual Sound). It also shows a version with a phase switch on the tone pot.

Related diagrams

Questions about your install? Email sales@bestbassgear.com.