Nordstrand Bass Wiring Diagrams

Nordstrand bass wiring diagrams, written out as text: all 15 Nordstrand sheets in our library. That's the eleven 2-band (2B) and 3-band (3B) preamp layouts, from the one-pickup 2B-3a to the five-knob 3B-5b and the MusicMan-style 2B-MM, plus the coil-switching sheets for Nordstrand dual coil, humbucker, MM and Fat Stack pickups. Find your layout for its controls and where the pickups go, then follow the hookup. Each has Nordstrand's original drawing and a PDF download.

Before you start

  • Nordstrand preamps switch the battery through the output jack: battery − to the jack's ring, so you need a stereo (TRS) jack and plugging in a mono lead turns the preamp on.
  • Volume, tone and blend pots are 250k audio taper and EQ pots are 50k linear on every sheet except the 2B-MM (25k volume, 1M treble, 100k bass).
  • Each sheet marks the pickup leads: 'To Pickup +', 'To Neck +', 'To Bridge +' and 'To Pickup −' (ground, on a pot casing).
  • The EQ pots connect to the board with three wires each, green, grey and blue, always in the same order.
  • Where a drawing's switch lugs or overlapping pot gangs are too small to read lead by lead, this page says what they do and tells you to follow the drawing. Those spots are marked FUNCTION-LEVEL.

Find your diagram

2-band preamps (2B board)

3-band preamps (3B board)

Pickup wiring (coil switching)

The hookups

Nordstrand diagrams by layout

2-band preamps (2B board)

2B-3a: 1 pickup, 3 knobs (pull-passive volume, treble, bass)

The simplest Nordstrand 2-band layout: one pickup into a 2B board, with a volume knob that pulls up for passive and separate treble and bass knobs.

2B-3a: 1 pickup, 3 knobs (pull-passive volume, treble, bass): controls
Volume (pull)Master volume; pull up for passive (preamp bypassed)
TrebleTreble cut/boost
BassBass cut/boost
EQ (2B board)Treble ±12 dB at 4 kHz, bass ±12 dB at 50 Hz
On the boardGain trim (labelled 0-15 dB gain on the drawing) and a treble curve switch: up = high treble curve, down = low treble curve
Pot valuesVolume, tone and blend pots 250k audio taper; EQ pots 50k linear taper (as printed on the drawing)
PowerOne 9 V battery, switched on by plugging into the stereo jack (battery − to the jack ring)
2B-3a: pickup leads: where the pickup goes
#FromToNotes
1Pickup +Volume pot, middle lug (marked on the drawing)As drawn
2Pickup −Volume pot casing (ground)
Nordstrand 2B-3a one-pickup 3-knob 2-band preamp wiring diagram
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

2B-3b: 2 pickups, 3 knobs (pull-passive volume, blend, stacked treble/bass)

Two pickups through a blend pot into the 2B board, with a pull-passive master volume and the treble and bass on one stacked (concentric) pot.

2B-3b: 2 pickups, 3 knobs (pull-passive volume, blend, stacked treble/bass): controls
Volume (pull)Master volume; pull up for passive
BlendNeck to bridge pickup mix
Treble/Bass stackTwo-gang concentric pot: treble on one ring, bass on the other
EQ (2B board)Treble ±12 dB at 4 kHz, bass ±12 dB at 50 Hz
On the boardGain trim (labelled 0-15 dB gain on the drawing) and a treble curve switch: up = high treble curve, down = low treble curve
Pot valuesVolume, tone and blend pots 250k audio taper; EQ pots 50k linear taper (as printed on the drawing)
PowerOne 9 V battery, switched on by plugging into the stereo jack (battery − to the jack ring)
2B-3b: pickup leads: where the pickups go
#FromToNotes
1Neck +Blend pot, neck input lugLabel 'To Neck +'
2Bridge +Blend pot, bridge input lugLabel 'To Bridge +'
3Both pickups −Blend pot casing (ground)Label 'To Pickup −'
Nordstrand 2B-3b two-pickup 3-knob 2-band preamp wiring diagram with blend and stacked treble bass
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

2B-4a: 2 pickups, 4 knobs (pull-passive volume, volume, treble, bass)

Jazz-style volume/volume: each pickup has its own volume pot. The neck volume also pulls up for passive. Treble and bass are separate knobs.

2B-4a: 2 pickups, 4 knobs (pull-passive volume, volume, treble, bass): controls
Neck volume (pull)Neck pickup volume; pull up for passive
Bridge volumeBridge pickup volume
TrebleTreble cut/boost
BassBass cut/boost
EQ (2B board)Treble ±12 dB at 4 kHz, bass ±12 dB at 50 Hz
On the boardGain trim (labelled 0-15 dB gain on the drawing) and a treble curve switch: up = high treble curve, down = low treble curve
Pot valuesVolume, tone and blend pots 250k audio taper; EQ pots 50k linear taper (as printed on the drawing)
PowerOne 9 V battery, switched on by plugging into the stereo jack (battery − to the jack ring)
2B-4a: pickup leads: where the pickups go
#FromToNotes
1Neck +Pull-passive volume pot, middle lugLabel 'To Neck +'
2Bridge +Second volume pot, middle lugLabel 'To Bridge +'
3Both pickups −Second volume pot casing (ground)Label 'To Pickup −'
4Volume pots, outer lugJoined to each other and on to the pull switchGrey wire on the drawing
Nordstrand 2B-4a two-pickup 4-knob volume volume treble bass preamp wiring diagram
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

2B-4b: 2 pickups, 4 knobs (pull-passive volume, blend, treble, bass)

Master volume (pull for passive), a blend pot between the two pickups, and separate treble and bass knobs on the 2B board.

2B-4b: 2 pickups, 4 knobs (pull-passive volume, blend, treble, bass): controls
Volume (pull)Master volume; pull up for passive
BlendNeck to bridge pickup mix
TrebleTreble cut/boost
BassBass cut/boost
EQ (2B board)Treble ±12 dB at 4 kHz, bass ±12 dB at 50 Hz
On the boardGain trim (labelled 0-15 dB gain on the drawing) and a treble curve switch: up = high treble curve, down = low treble curve
Pot valuesVolume, tone and blend pots 250k audio taper; EQ pots 50k linear taper (as printed on the drawing)
PowerOne 9 V battery, switched on by plugging into the stereo jack (battery − to the jack ring)
2B-4b: pickup leads: where the pickups go
#FromToNotes
1Neck +Blend pot, neck input lugLabel 'To Neck +'
2Bridge +Blend pot, bridge input lugLabel 'To Bridge +'
3Both pickups −Blend pot casing (ground)Label 'To Pickup −'
Nordstrand 2B-4b two-pickup 4-knob volume blend treble bass preamp wiring diagram
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

2B-4c: 2 pickups, 4 knobs (pull-passive volume, blend, passive tone, stacked treble/bass)

Like the 2B-3b with a fourth knob: a passive tone control (250k pot with a .047 µF capacitor) between the blend and the preamp.

2B-4c: 2 pickups, 4 knobs (pull-passive volume, blend, passive tone, stacked treble/bass): controls
Volume (pull)Master volume; pull up for passive
BlendNeck to bridge pickup mix
Passive toneTreble roll-off, 250k pot and .047 µF capacitor; works in active and passive
Treble/Bass stackTwo-gang concentric pot
EQ (2B board)Treble ±12 dB at 4 kHz, bass ±12 dB at 50 Hz
On the boardGain trim (labelled 0-15 dB gain on the drawing) and a treble curve switch: up = high treble curve, down = low treble curve
Pot valuesVolume, tone and blend pots 250k audio taper; EQ pots 50k linear taper (as printed on the drawing)
PowerOne 9 V battery, switched on by plugging into the stereo jack (battery − to the jack ring)
2B-4c: pickup leads and tone: where the pickups go
#FromToNotes
1Neck +Blend pot, neck input lugLabel 'To Neck +'
2Bridge +Blend pot, bridge input lugLabel 'To Bridge +'
3Both pickups −Blend pot casing (ground)Label 'To Pickup −'
4.047 µF capacitorTone pot: one end on a lug, the other to the tone pot casingTone pot casing is grounded
5Blend outputTone pot, and on to the volume / pull switchGrey wires on the drawing
Nordstrand 2B-4c two-pickup 4-knob preamp wiring diagram with passive tone
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

2B-MM: MusicMan-style 3 knobs (volume, treble, bass)

The 2B-MM board for a single Music Man-style pickup: volume, treble and bass, no blend and no passive switch. It uses different pot values from the other 2B sheets.

2B-MM: MusicMan-style 3 knobs (volume, treble, bass): controls
VolumeMaster volume, 25k audio
TrebleTreble, 1M audio
BassBass, 100k audio
PowerOne 9 V battery, switched by the stereo jack's ring
2B-MM: wire by wire
#FromToNotes
1Board left pin 1 (black)Volume pot right lug and casingGround. The casing also runs to the jack sleeve and to the bass and treble pot casings
2Board left pins 2-4 (green, grey, blue)Treble pot lugs, left to right as drawnTreble pot 1M audio
3Board left pin 5 (yellow)Volume pot left lugPreamp output into the volume pot
4Volume pot middle lugJack tipGrey wire
5Board right pin 1 (orange)Pickup +Label 'To Pickup +'
6Board right pins 2-3 (grey, green)Bass pot middle and left lugsBass pot 100k audio; its right lug is unused
7Board right pin 4 (red)Battery +
8Battery −Jack ringStereo jack: plugging in turns the preamp on
9Jack sleeveVolume pot casingBlack wire
10Pickup −Ground (pot casing)Not drawn on this sheet; ground it as on the other Nordstrand sheets
Nordstrand 2B-MM MusicMan style 2-band preamp wiring diagram
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Step by step

  1. Solder the treble pot to the board's left pins 2-4 (green, grey, blue) and the bass pot's middle and left lugs to right pins 2-3 (grey, green).
  2. Connect the board's left pin 5 (yellow) to the volume pot's left lug, and the volume's middle lug to the jack tip.
  3. Connect the board's right pin 1 (orange) to the pickup +, and ground the pickup −.
  4. Connect right pin 4 (red) to battery +, battery − to the stereo jack's ring.
  5. Connect left pin 1 (black) to the volume pot's right lug and casing, and chain the casing to the jack sleeve and the bass and treble pot casings.
  6. Test: plug in, tap the pickup, check volume, treble and bass.

Wire it with

3-band preamps (3B board)

3B-3: 1 pickup, 3 knobs (pull-passive volume, pull mid with frequency select, stacked treble/bass)

One pickup into the 3B board. The volume pulls up for passive, the mid knob pulls to change the mid frequency, and treble and bass share a stacked pot.

3B-3: 1 pickup, 3 knobs (pull-passive volume, pull mid with frequency select, stacked treble/bass): controls
Volume (pull)Master volume; pull up for passive
Mid (pull knob)Mid cut/boost; pull the knob to switch the mid frequency between 1 kHz and 400 Hz
Treble/Bass stackTwo-gang concentric pot
EQ (3B board)Treble ±12 dB at 4 kHz, mid ±12 dB at 1 kHz or 400 Hz, bass ±12 dB at 50 Hz
On the boardGain trim (labelled 0-15 dB gain on the drawing)
Pot valuesVolume, tone and blend pots 250k audio taper; EQ pots 50k linear taper (as printed on the drawing)
PowerOne 9 V battery, switched on by plugging into the stereo jack (battery − to the jack ring)
3B-3: pickup leads: where the pickup goes
#FromToNotes
1Pickup +Volume pot, the lug marked on the drawingLabel 'To Pickup +'
2Pickup −Volume pot casing (ground)Label 'To Pickup −'
Nordstrand 3B-3 one-pickup 3-knob 3-band preamp wiring diagram
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

3B-4a: 2 pickups, 4 knobs (stacked volume/volume, pull-passive tone, pull mid, stacked treble/bass)

Jazz-style volume/volume on one stacked pot, a passive tone knob that also pulls up for passive mode, a pull mid knob and a stacked treble/bass.

3B-4a: 2 pickups, 4 knobs (stacked volume/volume, pull-passive tone, pull mid, stacked treble/bass): controls
Volume/Volume stackNeck volume on one ring, bridge volume on the other
Tone (pull)Passive tone with a .047 µF capacitor; pull up for passive (preamp bypassed)
Mid (pull knob)Mid cut/boost; pull the knob to switch the mid frequency between 1 kHz and 400 Hz
Treble/Bass stackTwo-gang concentric pot
EQ (3B board)Treble ±12 dB at 4 kHz, mid ±12 dB at 1 kHz or 400 Hz, bass ±12 dB at 50 Hz
On the boardGain trim (labelled 0-15 dB gain on the drawing)
Pot valuesVolume, tone and blend pots 250k audio taper; EQ pots 50k linear taper (as printed on the drawing)
PowerOne 9 V battery, switched on by plugging into the stereo jack (battery − to the jack ring)
3B-4a: pickup leads: where the pickups go
#FromToNotes
1Neck +Stacked volume pot, neck gangLabel 'To Neck +'
2Bridge +Stacked volume pot, bridge gangLabel 'To Bridge +'
3Both pickups −Volume pot casing (ground)Label 'To Pickup −'
4Volume outputsTone pot and on to the pull switch on the tone potGrey wires on the drawing
Nordstrand 3B-4a two-pickup 4-knob 3-band preamp wiring diagram with stacked volumes
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

3B-4b: 2 pickups, 4 knobs (stacked volume/tone, blend, pull mid, stacked treble/bass)

A stacked volume and passive tone, a blend pot, a pull mid knob and a stacked treble/bass. This sheet has no active/passive switch: the board output goes straight to the jack.

3B-4b: 2 pickups, 4 knobs (stacked volume/tone, blend, pull mid, stacked treble/bass): controls
Volume/Tone stackVolume on one ring, passive tone (.047 µF) on the other
BlendNeck to bridge pickup mix
Mid (pull knob)Mid cut/boost; pull the knob to switch the mid frequency between 1 kHz and 400 Hz
Treble/Bass stackTwo-gang concentric pot
EQ (3B board)Treble ±12 dB at 4 kHz, mid ±12 dB at 1 kHz or 400 Hz, bass ±12 dB at 50 Hz
On the boardGain trim (labelled 0-15 dB gain on the drawing)
Pot valuesVolume, tone and blend pots 250k audio taper; EQ pots 50k linear taper (as printed on the drawing)
PowerOne 9 V battery, switched on by plugging into the stereo jack (battery − to the jack ring)
3B-4b: pickup leads and output: where the leads go
#FromToNotes
1Neck +Blend pot, neck input lugLabel 'To Neck +'
2Bridge +Blend pot, bridge input lugLabel 'To Bridge +'
3Both pickups −Blend pot casing (ground)Label 'To Pickup −'
4Board output (yellow)Jack tipDirect; no passive switch on this layout
5Volume/tone stackBoard input (orange)Blend output feeds the stack, then the board
Nordstrand 3B-4b two-pickup 4-knob 3-band preamp wiring diagram with volume tone stack
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

3B-5a: 2 pickups, 5 knobs (pull-passive volume, blend, treble, pull mid, bass)

The five-knob 3-band layout with every control on its own knob: master volume (pull for passive), blend, treble, mid (pull for frequency) and bass.

3B-5a: 2 pickups, 5 knobs (pull-passive volume, blend, treble, pull mid, bass): controls
Volume (pull)Master volume; pull up for passive
BlendNeck to bridge pickup mix
TrebleTreble cut/boost
Mid (pull knob)Mid cut/boost; pull the knob to switch the mid frequency between 1 kHz and 400 Hz
BassBass cut/boost
EQ (3B board)Treble ±12 dB at 4 kHz, mid ±12 dB at 1 kHz or 400 Hz, bass ±12 dB at 50 Hz
On the boardGain trim (labelled 0-15 dB gain on the drawing)
Pot valuesVolume, tone and blend pots 250k audio taper; EQ pots 50k linear taper (as printed on the drawing)
PowerOne 9 V battery, switched on by plugging into the stereo jack (battery − to the jack ring)
3B-5a: pickup leads: where the pickups go
#FromToNotes
1Neck +Blend pot, neck input lugLabel 'To Neck +'
2Bridge +Blend pot, bridge input lugLabel 'To Bridge +'
3Both pickups −Blend pot casing (ground)Label 'To Pickup −'
Nordstrand 3B-5a two-pickup 5-knob 3-band preamp wiring diagram
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

3B-5b: 2 pickups, 5 knobs (pull-passive volume, blend, passive tone, pull mid, stacked treble/bass)

Master volume (pull for passive), blend, a passive tone (.047 µF), a pull mid knob and a stacked treble/bass.

3B-5b: 2 pickups, 5 knobs (pull-passive volume, blend, passive tone, pull mid, stacked treble/bass): controls
Volume (pull)Master volume; pull up for passive
BlendNeck to bridge pickup mix
Passive toneTreble roll-off, .047 µF capacitor
Mid (pull knob)Mid cut/boost; pull the knob to switch the mid frequency between 1 kHz and 400 Hz
Treble/Bass stackTwo-gang concentric pot
EQ (3B board)Treble ±12 dB at 4 kHz, mid ±12 dB at 1 kHz or 400 Hz, bass ±12 dB at 50 Hz
On the boardGain trim (labelled 0-15 dB gain on the drawing)
Pot valuesVolume, tone and blend pots 250k audio taper; EQ pots 50k linear taper (as printed on the drawing)
PowerOne 9 V battery, switched on by plugging into the stereo jack (battery − to the jack ring)
3B-5b: pickup leads: where the pickups go
#FromToNotes
1Neck +Blend pot, neck input lugLabel 'To Neck +'
2Bridge +Blend pot, bridge input lugLabel 'To Bridge +'
3Both pickups −Blend pot casing (ground)Label 'To Pickup −'
4Blend outputTone pot and the volume / pull switchGrey wires on the drawing
Nordstrand 3B-5b two-pickup 5-knob 3-band preamp wiring diagram with passive tone
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

Pickup wiring (coil switching)

Dual coil pickups: series / single / parallel switch

Nordstrand's dual coil (twin-coil soapbar) pickups have four leads, so each pickup can be switched between both coils in series, one coil, or both coils in parallel.

Dual coil pickups: series / single / parallel switch: controls
Switch3-position on-on-on DPDT mini toggle per pickup, labelled parallel (up), single (centre), series (down) as drawn
Leads4 conductors (red, white, black, green) plus the bare shield
Nordstrand dual coil pickup series single parallel switch wiring diagram
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

Humbucker pickups: series / single / parallel switch

The same four-lead switching as the dual coil sheet, drawn for Nordstrand's humbucking pickups. The lead colours and switch lugs are identical.

Humbucker pickups: series / single / parallel switch: controls
Switch3-position on-on-on DPDT mini toggle per pickup, labelled parallel (up), single (centre), series (down) as drawn
Leads4 conductors (red, white, black, green) plus the bare shield
Nordstrand humbucker pickup series single parallel switch wiring diagram
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

MM (Music Man-style) pickups: series / single / parallel switch

The same four-lead switching again, drawn for Nordstrand's MM-shape pickups (MM4, MM5 and similar).

MM (Music Man-style) pickups: series / single / parallel switch: controls
Switch3-position on-on-on DPDT mini toggle per pickup, labelled parallel (up), single (centre), series (down) as drawn
Leads4 conductors (red, white, black, green) plus the bare shield
Nordstrand MM Music Man style pickup series single parallel switch wiring diagram
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

Fat Stack pickups: single coil / hum-cancelling switch

Nordstrand Fat Stacks are stacked hum-cancelling J pickups with three leads plus shield. One 2-way DPDT switch sets both pickups to single coil or hum-cancelling together.

Fat Stack pickups: single coil / hum-cancelling switch: controls
Switch2-way (on-on) DPDT: up = single coil, down = hum-cancelling (both pickups at once)
Leads per pickupWhite (+), red (coil link), black (−), plus a small grey shield wire
Fat Stack coil switch: wire by wire
#FromToNotes
1Neck white (+)Blend pot, neck inputLabel 'to blend'
2Bridge white (+)Blend pot, bridge inputLabel 'to blend'
3Neck redSwitch, middle row, left lug
4Bridge redSwitch, middle row, right lug
5Switch, bottom row: both lugsJoined together, then to ground
6Neck black (−)Ground
7Bridge black (−)Ground
8Both pickups' small grey (shield) wiresGroundNote on the drawing
9Switch, top rowNo wires

Step by step

  1. Fit a 2-way (on-on) DPDT mini toggle where you want the coil switch.
  2. Run each pickup's white (+) lead to its input on the blend pot: neck to the neck side, bridge to the bridge side.
  3. Solder the neck red lead to the switch's middle-left lug and the bridge red lead to the middle-right lug.
  4. Join the two bottom lugs with a short jumper and run a wire from them to ground.
  5. Solder both black (−) leads and both small grey shield wires to ground.
  6. Test: lever up = single coil, lever down = hum-cancelling (both coils).
Nordstrand Fat Stack coil switch DPDT wiring diagram
Nordstrand's wiring drawing. Click to enlarge, or download the PDF.

Wire it with

The hookups

Nordstrand 2B 2-band board: battery, jack, input, output and EQ pots, wire by wire

Every 2B sheet except the 2B-MM uses the same 2B board with ten pins down its left edge. Top to bottom they are: output, input, battery +, ground, then three for the treble pot and three for the bass pot.

You need: Nordstrand 2B board with its treble and bass pots, a 9 V battery clip, a stereo (TRS) output jack, your volume / blend pots.

Nordstrand 2B board pin order example from the 2B-3a sheet
Nordstrand's drawing (this one shown as the example). Click to enlarge, or download the PDF.
2B board: wire by wire
#FromToNotes
1Pin 1 (yellow)Output: to the pull-passive switch, or the jack tip if you have no switchPreamp output
2Pin 2 (orange)Input: from the volume / blend / tone output, via the pull switchPreamp input
3Pin 3 (red)Battery +
4Pin 4 (black)Ground: jack sleeve and the pot casings
5Pins 5-7 (green, grey, blue)Treble pot lugs, left to right as drawn50k linear
6Pins 8-10 (green, grey, blue)Bass pot lugs, left to right as drawn50k linear
7Battery −Jack ringPlugging in turns the preamp on
8Jack sleeveGround (pot casing)
9Jack tipPull-passive switch (or board output)Grey wire on the drawings
10All pot casingsGround, chained togetherBlack wires on the drawings

Step by step

  1. Lay out the pots and board, and note which pot is volume, blend, treble and bass for your sheet.
  2. Solder the treble pot to the three treble pins (green, grey, blue) and the bass pot to the three bass pins, keeping the colour order.
  3. Wire the pickups to the volume or blend pot as your sheet shows (pickup + to the marked lug, pickup − to the casing).
  4. Connect board black to ground, red to the battery +, and the battery − to the stereo jack's ring.
  5. Connect the board's orange input and yellow output to the pull-passive switch as drawn, and the switch to the jack tip.
  6. Chain all pot casings to ground and the jack sleeve.
  7. Test: plug in (this turns on the battery), tap the pickups, check the EQ, then pull the volume for passive. Set the gain trim and treble curve switch on the board to taste.
  • The 2B-MM board has its pins on two sides and its own wiring table in the 2B-MM section above.
  • The treble curve switch on the board: up = high treble curve, down = low treble curve.

Nordstrand 3B 3-band board: battery, jack, input, output, EQ pots and mid frequency switch

The 3B board has its EQ pins along the bottom edge (treble, mid, bass, three each) with the output at the right end, the battery + on the left edge, and the input and ground at the top corners.

You need: Nordstrand 3B board with treble, mid (push-pull) and bass pots, a 9 V battery clip, a stereo (TRS) output jack, your volume / blend pots.

Nordstrand 3B board pin layout example from the 3B-5a sheet
Nordstrand's drawing (this one shown as the example). Click to enlarge, or download the PDF.
3B board: wire by wire
#FromToNotes
1Top left, by the gain trim (orange)Input: from the volume / blend / tone output, via the pull switch
2Top right (black)Ground: jack sleeve and pot casings
3Left edge (red)Battery +
4Bottom: 3 TREBLE pins (green, grey, blue)Treble pot lugs, left to right as drawn50k linear
5Bottom: 3 MID pins (green, grey, blue)Mid pot lugs, left to right as drawn50k linear, push-pull
6Two grey wires from the middle of the boardMid pot's pull switchFrequency select. FUNCTION-LEVEL: follow the drawing
7Bottom: 3 BASS pins (green, grey, blue)Bass pot lugs, left to right as drawn50k linear
8Bottom right end (yellow)Output: to the pull-passive switch, or straight to the jack tip (3B-4b)
9Battery −Jack ring
10Jack sleeveGround

Step by step

  1. Solder the treble, mid and bass pots to their three pins each, keeping the green, grey, blue order.
  2. Run the two grey frequency-select wires from the board to the mid pot's pull switch, with the switch's capacitors as drawn.
  3. Wire the pickups to the volume or blend pot as your sheet shows.
  4. Connect the board's black to ground, red to battery +, and the battery − to the stereo jack's ring.
  5. Connect the orange input and yellow output to the pull-passive switch as drawn (on the 3B-4b, yellow goes straight to the jack tip).
  6. Chain all pot casings to ground and the jack sleeve.
  7. Test: plug in, tap the pickups, check each EQ band, pull the mid knob to hear the frequency change, then try passive mode.
  • FUNCTION-LEVEL: the mid pot's pull switch and its two small capacitors are drawn too small to read the values. Follow the drawing for which lugs they bridge.
  • Mid frequency: 1 kHz or 400 Hz, chosen by pulling the mid knob.

Pull-passive switch: bypassing the preamp with a push-pull pot

On most Nordstrand sheets the master volume (on the 3B-4a, the tone) is a push-pull pot. Its DPDT switch picks what reaches the jack tip: the preamp output (active) or the volume/blend signal straight past the board (passive, pulled up).

Nordstrand pull-passive volume push-pull switch example
Nordstrand's drawing (this one shown as the example). Click to enlarge, or download the PDF.
Pull-passive switch: FUNCTION-LEVEL, follow the drawing for exact lugs
#FromToNotes
1Jack tipSwitch common lugGrey wire
2Board output (yellow)Switch: active-side lug
3Board input (orange)Switch: the other poleFeeds the board from the volume / blend
4Volume / blend outputSwitch: passive-side lug and the input poleGrey wires
  • FUNCTION-LEVEL: the push-pull switch's six lugs are drawn small and the grey jumpers cross; this table says what each lead does. Copy the lug positions from your sheet's drawing.
  • Passive mode still uses the volume, blend and passive tone; only the board (and its EQ) is bypassed. The battery is still switched by the jack.

Blend and volume pots: where the neck and bridge pickups go

Two-pickup Nordstrand sheets either blend (one dual-gang 250k blend pot) or use two volume pots. Every sheet marks where each pickup goes with 'To Neck +', 'To Bridge +' and 'To Pickup −'.

Nordstrand blend pot pickup connections example
Nordstrand's drawing (this one shown as the example). Click to enlarge, or download the PDF.
Blend / volume pots: where the pickups go (FUNCTION-LEVEL for the blend's gang lugs)
#FromToNotes
1Neck pickup +The lug marked 'To Neck +'One gang of the blend pot (or the neck volume)
2Bridge pickup +The lug marked 'To Bridge +'The other gang (or the bridge volume)
3Both pickups −Pot casing, marked 'To Pickup −'Ground
4Blend / volume outputsJoined, then to the tone pot or pull-passive switchGrey wires
5Remaining outer lugsGround (casing)Black jumpers
  • FUNCTION-LEVEL: the blend pot's two gangs are drawn overlapping; follow the drawing for which gang carries neck and which carries bridge.
  • Four-lead pickups: the '+' here is the output from that pickup's coil switch (see the coil switch hookup).

4-conductor Nordstrand pickups: series / single / parallel switch, wire by wire

The dual coil, humbucker and MM sheets wire each four-lead Nordstrand pickup to its own 3-position on-on-on DPDT mini toggle: lever up = parallel, centre = single coil, down = series. Lugs are named as drawn, looking at the back of the switch with the lever on the left.

You need: One 3-way on-on-on DPDT mini toggle per pickup, the pickup's 4 leads plus shield.

Nordstrand four-conductor pickup series single parallel switch drawing
Nordstrand's drawing (this one shown as the example). Click to enlarge, or download the PDF.
Neck pickup switch: wire by wire
#FromToNotes
1RedTop-right lugPlus a red jumper from top-right to middle-left
2WhiteMiddle-right lug
3BlackBottom-left lug
4Bottom-left lugPickup output (+): to the blend / volume
5GreenBottom-right lug
6Bottom-right lugGround
7Bare shieldGround
8Top-left lugNo wire
Bridge pickup switch: wire by wire
#FromToNotes
1WhiteTop-right lugPlus a white jumper from top-right to middle-left
2RedMiddle-right lug
3GreenBottom-left lug
4Bottom-left lugGround
5BlackBottom-right lug
6Bottom-right lugPickup output (+): to the blend / volume
7Bare shieldGround
8Top-left lugNo wire

Step by step

  1. Fit one 3-way on-on-on DPDT mini toggle per pickup.
  2. Neck: red to top-right with a jumper to middle-left, white to middle-right, black to bottom-left, green to bottom-right.
  3. Neck: take the output from bottom-left to the blend or volume, and ground bottom-right and the bare shield.
  4. Bridge: white to top-right with a jumper to middle-left, red to middle-right, green to bottom-left, black to bottom-right.
  5. Bridge: ground bottom-left and the bare shield, and take the output from bottom-right to the blend or volume.
  6. Test each pickup in all three lever positions: up = parallel, centre = single coil, down = series.
  • The neck and bridge are drawn differently (red and white swap at the top, black and green swap at the bottom). Wire each pickup as its own table shows.
  • Series is the fullest and loudest, parallel is brighter and lower output, single coil uses one coil only and is not hum-cancelling.

FAQ

Why does a Nordstrand preamp need a stereo jack?

The battery's black (−) wire goes to the jack's ring. A normal mono lead joins ring to sleeve when it's plugged in, which turns the preamp on. Unplug when you're done, or the battery stays connected.

What does the pull-passive volume do?

Pulling the knob up sends the volume (and blend and passive tone) signal straight to the jack, bypassing the 2B or 3B board and its EQ. It gets you playing if the battery dies.

What is the switch on the Nordstrand 2B board?

It sets the treble curve: switch up for the high treble curve, down for the low treble curve. The small trim pot beside it sets the board's overall gain.

How do I change the mid frequency on a Nordstrand 3B preamp?

Pull the mid knob. Its switch moves the mid band between 1 kHz and 400 Hz.

Can a Nordstrand 2B or 3B run on 18 volts?

Yes. The drawings show one 9 V battery, but adding a second battery for 18 V gives more headroom and longer battery life. An alkaline 9 V lasts about 180 hours.

What do series, single and parallel do on a Nordstrand dual coil, humbucker or MM pickup?

Series uses both coils one after the other for the fullest, loudest sound. Parallel uses both side by side for a brighter, slightly quieter sound. Single uses one coil only, which is the brightest but not hum-cancelling.

Which pot values do Nordstrand preamps use?

Volume, tone and blend pots are 250k audio taper and EQ pots are 50k linear. The 2B-MM board is different: 25k audio volume, 1M audio treble and 100k audio bass.

Related

Questions about a hookup? Call 877-839-3531 or email sales@bestbassgear.com.