Accessories

The B245 EMG Pickup Buss is used on two pickup guitars that have a selection switch. The buss provides a convenient way to install either Active or Passive EMG Pickups without soldering.

The B289 switch is a low profile solderless 3 way toggle switch designed to fit standard Gibson style guitars. All switches use EMG’s "BNOG" connector arrangement and include 2 cables (short & long) for easy connection to EMG’s connection buss....

This North American built toggle switch is beefy and holds up to the rigors of rock & roll. Available in a black or ivory tip with the specific design being "one size fits all" solderless toggle for all Gibson models. The ease of solderless installation...

25k Balance Potentiometer for use with active pickups
25k Solid Shaft Blend/Balance Potentiometer

EMG 25k Stack Volume/Volume or Volume/Tone for EMG Active pickups. Solderless
EMG 25k Stack Volume/Volume or Volume/Tone for EMG Active pickups. Comes with concentric knob, output jack, interconnecting cables, and allen key

Comes with concentric knob, capacitor, wiring diagram, and allen key
EMG 25k Stack Volume/Volume or Volume/Tone for EMG Active pickups. Comes with concentric knob, capacitor, wiring diagram, and allen key

25k Ohm Active Balance Control
The ABC is an active EQ accessory that eliminates insertion loss and is designed to work with all our non-X series pickups that use a standard EMG tone pot. Insertion loss is a naturally occurring yet frustrating phenomenon that occurs most frequently...

solderless/modular EMG 25K SPL Control Volume Push Pull Potentiometer
25k Push-Pull pot for use with EMG pickups such as 35,40,45TW or any EMG pickup that requires use of a push pull pot on the Dual Mode pickups that require them.

EMG 25k Solderless Volume Potentiometer
25k Split-Shaft Volume Pot. Solderless short shaft.

X-Series ABCX Active Balance Control
The ABCX is an active EQ accessory that eliminates insertion loss and is designed to work with all our X series pickups that have an active tone pot. Insertion loss is a naturally occurring yet frustrating phenomenon that occurs most frequently with...

The GrooveTech Jack and Pot Wrench provides three thin-wall sockets - 1/2", 7/16", and 12mm - in a compact four-inch tool to handle the most common sizes of jacks and pots on instruments, amps, and other audio gear.
Instrument and amp jacks are notorious for coming loose. And with a shallow nut and recessed cavity, access can be challenging. Until now, that is. The GrooveTech Jack and Pot Wrench provides three thin-wall sockets - 1/2", 7/16", and 12mm - in a compact...

EMG Concentric Single knob for EMG preamps and controls.
EMG single fluted knob. 6mm inner diameter.

EMG Concentric Upper knob for EMG preamps and controls.
EMG Fluted Black Plastic Concentric Knob found on stacked EMG Preamp Controls. Upper knob only.

EMG Concentric Black Plastic Lower Knob
EMG Concentric Black Plastic Lower knob. Inner Diamter 8mm.

The GrooveTech kit provide everything you need to work on your bass, and an Easy Setup Guide is included that takes the mystery out of it.
Have tool kit; will travel. Bass players may know a little about truss rods and action, but few actually attempt adjustment. That's a shame, because a substantial upgrade in your performance can be realized with a properly set up axe. The GrooveTech kit...

Standard Driver provides firm contact over the entire slot width for damage-free adjustment.
Vintage-style truss rod nuts have very thin yet wide slots and are made of unhardened steel, so normal slotted screwdrivers will cause damage - as evidenced on many vintage guitars and basses. We developed two screwdrivers specifically for this application....

The Cheater Driver allows quick minor adjustment without removing the neck
Vintage-style truss rod nuts have very thin yet wide slots and are made of unhardened steel, so normal slotted screwdrivers will cause damage - as evidenced on many vintage guitars and basses. We developed two screwdrivers specifically for this application....

The first multi-tool for guitars and basses that's actually useful, without unnecessary gimmicks.
New Second Generation Design Introduced in 2008 - the original GrooveTech Multi-Tool was an instant hit with guitar and bass players alike. Never before had a multi-tool provided such functionality or made use of pro-grade components. Despite...

The EMG AB (Afterburner) is a boost you can use instead of your tone or volume knob (does not function as a tone or volume) and activate with our variable gain push/pull pot. When the Push-Pull pot is in the “down” position there is no boost and the...

#3-48 Screws, 1in. length
EMG H Screw and Spring Set #3-48 Screws, 1'' length: Two (2) screws and two (2) springs used for height adjustment on humbuckers mounted onto a pickguard or pickup ring.

Solderless Pickup Cable for EMG pickups
EMG Solderless Pickup Cable For replacement solderless applications or converting your existing EMG's with quick connect cable option to be solderless in conjunction with EMG preamps or controls 9" in Length Sold Individually

CruzTools Bass Stagehand Compact Kit
Our GrooveTech Tech Kits are the ultimate tool kits for any guitar and bass player, but musicians who want something more portable may now consider the new StageHand kit. It provides comparable capability, yet in a compact package and budget priced. Central...

SIT Powerwound Nickel or Stainless Steel 4, 5, and 6 String Bass Strings
Nickel Plated or Stainless Steel cover wrap. Swedish Steel hex core. Round Wound .Our top selling bass sets - excellent for all styles of music. Available String Sets 4-String Stainless Steel Medium...